Techtonic Electric Standing Desk Converter wIth Triple Monitor Mount, 3 Screen Support, Quiet Sit-Stand Desk with Button Control, Keyboard Tray, Ideal for Gaming & Computer Work (Black)

This product is the only one I could find that worked with 3 monitors. It is a tight squeeze with my Dell 24" monitors, but I was able to make it work.The power lift works reasonably fast and quietly and stays put where you set it along its path of travel. There is sufficient working space on the top platform to lay out several pieces of paper or a small notebook while working.It is reasonably easy to put together, but it does take some time to get it all together and set up properly.The two minor issues I had with it are:The monitor mounts are larger than the recessed opening on the back of my Dell monitors. I could have trimmed the mount points a bit to make them fit, but I decided to get some spacers and longer screws that were slightly longer than the depth of the recessed area on the back of my monitors. I found what I needed at my local hardware store for less than $10.00The lower tray does not sit flat against your desk, I had to add some 1/4" adhesive pads to the bottom of the lower keyboard shelf to stabilize it for use while seated. This issue is not as noticeable when using this in standing position, though it does move a bit and is not rock steady when it is raised up.

I had previously ordered a different stand up desk convertor that was never delivered (damaged in shipment). I then re-ordered that same product as well as ordered this product. This product came first. I am very happy with everything about this stand up desk convertor and especially the spacious workspace/desk top space. The electric motor is really nice - very quiet, smooth and moves up and down quickly and steadily. Product is very sturdy. It is heavy; but once assembled, it is fairly easy to slide/move on your desk to where you want it. When mounting the monitors, I would recommend that you mount the center monitor first, then the two outside ones. I have three monitors mounted - two 23" and one 24". Would recommend this product.

The media could not be loaded. This is an update to my review below. Didn’t want to take the chance to wait do you notice any damage. I was extremely surprised to find the packaging inside the cardboard box protected the stand. It was very easy to assemble. ThanksAt this time I cannot rate the: eases of assemble, sturdiness or ergonomic. After Xmas I will complete those areas.This was purchased as a Xmas gift and will not be opened until the 25th of December.. I am very concerned on how the package was received and the taping of the box, which leaves a lot to be desired.Hopefully the video was attached because the system that is used does not allow me to confirm that it was.

Just completed assembly and set up of my 3 monitor Stand Steady (SS). Want to share my experience regarding delivery, assembly and quality of the product.To begin, I want to thank Stand Steady for their very fast responses to emailed questions and for assistance with the issues I experienced. In the end, my challenges with assembling the unit were non-issues. 1) Lower shelf screws: After full assembly, the motor calibration ensures that the lower shelf screws do not contact my desktop. 2) Center VESA mount: This was user error (me) because I failed to notice that the 3 monitor unit is only rated for 19 inch monitors. Mine are 21 inches. So my ordeal was self-induced.Delivery - Product was sent by US Mail. The post office knowingly did not deliver my package to my door. Instead (likely because the unit comes in one 70lb box .. heavy), the postal worker (who I saw thru my office window) merely put a note in my mailbox stating that the box was too big for my mailbox. So I drove to the post office and picked it up. Upon opening the box, I was pleased by how very well packed all the items were. No damage, so points to SS. However @SS, please co-ordinate with USPS to ensure the box is delivered to the door or to communicate buyers that it should be picked up.Assembly - All parts were in the box. 2 of the parts had defects. Minor: The lower shelf mounting brackets did not have recessed holes so the screws jut out and caused concern about scratching the desk. After full assembly, the concern abated because the lift motor seems to be calibrated to stop 1/4in above the desk so no scratching. For me, this is ok but the motor calibration may differ for others. Major: The center monitor bracket VESA mount was left misaligned by 1/2 inch (ie. A LOT). From a close look, the design specification did not consider that when the metal is stamped and folded the VESA mount hole would be left-shifted versus the center of the motor riser. The misalignment made it impossible to properly install my left monitor (I have 3 21" units). To compensate, I did the following: removed the center mount, cut off the small L-shaped tongue used to secure it to the riser with a screw, cut off half of the 2 riser 'shoes' the mount slides into and drilled 2 holes (for zip ties) into the metal backing on either side of the mount. I re-assembled the hacked mount and secured it to the motor riser with zip ties (since I had to cut off the screw tongue). Doing all this took nearly 2 hours, and earned me a reduction of the misalignment to 3/16 inch (still bad but allowed me to install my left monitor). After installing the monitors, they slumped down badly. The fix (this step is NOT in the assembly instructions and should be) was to: remove the monitors, remove the black center caps on the VESA mounts, tighten the VESA mount lock nuts, re-install the monitors.Quality - Notwithstanding the challenges, I still rate this a VERY good product and am glad I purchased it. My biggest concern was that the monitor arms or the shelves would not be strong enough. Boy was I pleased to discover that they are super strong! The monitor arms hold my heavy-ish old school DELLs with ease. I accidentally left a pencil holder under the left side of the upper shelf when lowering the unit. The motor rested the shelf on the pencil holder leaving me puzzled about why it didn't come down all the way, leaving the unit un-level. I finally realized--after checking--that the full weight of the assembly (plus monitors, approx 100lbs) was being supported by the left side of the upper shelf! NOW THAT'S STRONG! And the lower shelf is made of the same super strong material so is equally strong! This understanding of how strong the unit was made me more forgiving of the center VESA mount issue (which @SS, PLEASE FIX). Had the unit not be satisfactorily strong, my fallback purchase was a $1,000 Winston unit. As such, I'm overrall quite happy that I purchased this rock tough unit at a sub $400 price.So, in closing, the Stand Steady Techtonic Electric is a VERY good product on a bang-for-the-buck basis. I'm 6ft tall and it rises and lowers to very comfortable ergonomic positions for me. Due to the higher price of similar units, I would buy it again. OCO

I have been using this Stand Steady desktop converter for a little more than a month, now. I have my personal computer and my work laptops on this, and share (3) monitors between them (switchable). I share keyboard and have (2) mice. All of this is contained on the Stand Steady. The motor is powerful and does not strain at all standing and sitting positions. My only wish would be that they provide a settable stop for raising the desktop. I have a bookshelf that, if I am not careful, I would hit when standing up. Not critical, but would be a really nice feature. All in all, I am very happy with this purchase and would highly recommend.