Temporary Tooth Replacement Thermal Adhesive Fitting Beads for Fake Teeth for Snap On Instant and Denture Adhesive Fake Teeth Cosmetic Braces Veneer

This has 100% worked. But, I used Wotofo Mesh Strips as a “bridge” otherwise it wouldn’t have worked at all. (Wotofo available on Amazon) small black & green tube.My front crown tooth was completely knocked out leaving a gap.The tooth is broken so can’t be re-used.The Wotofo stainless steel mesh was necessary to create the bridge by sticking it with superglue (Loctite Gel UltraGel Control, blue cap), to the tooth at each side.To bridge a gap at the front:You’ll need:Old tweezersCotton wool pads (to dry area, and to roll up to absorb saliva.)Loctite SuperGlue GelBoiling water in a cupApprox 7 beadsSurgical bladesWotofo Mesh StripsTCPFirst, brush the area and swish with diluted TCP.1)Apply the SuperGlue (Loctite GEL UltraGel Control blue cap) to the tooth at each side of the gap.2)Take the Wotofo mesh with tweezers and position so it creates a bridge.3)Use bottom teeth to hold mesh bridge in whilst it sets (careful here, use a tap tap motion otherwise they’ll stick together).4)Once the “bridge” is set, take the best matching tooth (that you have already chosen and possibly filed down at the top arch), put in approx 5 or 6 beads QUICKLY put them in the replacement tooth, clench your teeth to hold the bridge in position and push the new tooth into position and hold. Keep clenching otherwise you’ll push the bridge off.Note. Clench your teeth whilst pushing the new tooth into position to prevent the mesh from being pushed off your teeth.This has worked amazingly well, I can honestly say that no one would know and the tooth is held in place Rock solid.I’d say the shade is A2, which is great as A1 is very white!Goes without saying, you should go to the dentist but, if like me you’re a 🐥 this is an alternative.You MUST make sure you have cleaned the area thoroughly (I used diluted TCP) and, make sure the area it’s dry.I also used a surgical blade to remove the excess plastic. (BE CAREFUL VERY SHARP)The mesh is amazing as the melted plastic seeps through it and sets behind it.I had the Wotofo as I’m a vaper, and the brainwave came to me to use it.It might take a couple of goes, but it will work. 😊👍🏽Ps. You should go to the dentist really, as infection can get in, then you’ll wish you had just gone in the first place. This hasn’t happed to me, but, I am VERY careful & make sure everything is CLEAN.Hope it works for you.

Waste of money. I managed to melt the beads and even managed to colour them with tea to make the material appear more realistic than the virgin white they are. However, I couldn't get the enamel caps provided to stick to the material, and I couldn't get the material to stick to my teeth either.

Honestly I was not expecting anything much from this at al. Was full prepared for it being useless and a waste of money.I recently knocked out my front tooth when having a seizure and I felt I looked absolutely horrible. Confidence shattered.I bought these and as I said, didn’t expect much. Upon arrival I wasn’t exactly sure what I was supposed to do.At first I just put around 12 of the balls in hot water (used the kettle) and they almost instantly went clear and sticky. I removed them from the water with a teaspoon and then pressed the mouldable substance into the gap in my mouth and tried to make a tooth shaped, well, tooth. Whilst waiting for it to cool and regarded I realised I may have had to use one of the teeth from the packet to stick tote surface of this sticky substance in my mouth. However it didn’t seem to be resolidifying at first. I took to mould out of my mouth and basically went to refute, however this time I use more of the mouldable balls (around 20). Put them in the hot water and then found the tooth from the packet that best looked like my original tooth. Trimmed and filed it to get the best fit possible.I took the mouldavle balls out of the water and stuck them to the back of the tooth I had made. With the excess mould behind the tooth I moulded that into a flatter surface against the roof of my mouth. Once I could feel it start to solidify (just got a little stiffer) I decided to take it out whilst keeping its shape and pop it in the freezer to quicken up the process. After taking it out the mould had fully hardened and I believe I’ve made the closest thing possible to a denture, without the big bills! The clear substance has also actually rewhitened once hardened so I may try again at making a whole tooth from the stuff! Either way, definitely worth the money if you need some temporary fix in pinch!

The putty is easily shaped, the veneers don’t stick that easily but I haven’t given up on them. It takes a while for the putty to firm up and cold water did help a little. My crown had broken so have used this protect the peg till I can get dental treatment. I am going to have a go at using with the broken crown as if it will bond enough it will be more aesthetically pleasing.

But certainly not for longterm use and quite hard toMould as hardens fast

I purchased these teeth from you because I struggle with my self confidence, so I was really keen to get the package which I did and to my disappointment your product doesn't work meaning the adhesive balls don't stick to teeth whatsoever so I expect a refund immediately or I will have to take the matter up with amazon, really disappointed with the service I received from you.