Kreg Accu-Cut XL, Circular Saw Track Guide, Cuts up to 100" Long, KMA3700

Good if you don't want to buy a track circular saw just yet. The track to saw plate has some wiggle, but it's fine if you apply some leftward pressure while cutting. The track never moves mid cut because of the grabby feet. It's pretty accurate but not table saw accurate as should be expected. Great value, good performance.

So much easier than getting that first plywood cut on a table say, even with help. The zero clearance edge makes set up fast. I don't even draw a line, just two measured dots and set the edge there. Drew a line and flipped it around for a second line to check the straightness in it as off 1/32 at the middle. Nice. It actually does stay put without clamps like the video. The aux clamps might be nice as the rubber ages, but so far so good. I store it in 4' sections on it's own shelf. The 4' length still stays put for those plywood cuts.

I picked this circular saw guide up to help cut 60"x60" Baltic Birch panels, which it does well. It allows me to cut them accurately and with much less shred on the cut edge. I had two issues with this product. The first is during setup they have you trim part of this plastic adhesive rail that you stick onto the aluminum bits so you get a zero clearance cut. Works fine, except that it melted a bunch of sticky gunk to the side of my brand-new blade, which wasn't fun. The second issue is the price. It's a few aluminum rails and a plastic sled. The rails are held together in the worst way (some soft set screws and rails you insert), not in some quick-to-use setup. Nothing about this is expensive, but here is a ~180 price tag. Could be much cheaper.

I recently used this to install hardwood stair treads and risers. I use a razor knife to mark cut lines for treads and risers as it is far more precise than a pencil line. With this track combined with my DeWalt cordless saw I was able to make perfectly accurate cuts on my razor cut line. Also made short work of breaking down a couple sheets of maple plywood for some built in shelves. I can see I wont be using my jobsite table saw nearly as much anymore. If you already have a cordless saw then this is a super cheap way to get into a track saw set up. I've used DeWalt's track saw a few times and Festool's several times and I can say that this is just as accurate. The only thing missing here is good dust collection but at this price point it really is a non issue. If you've been wanting a track saw but didn't want to spend the 500-700 dollars for the name brands this set up does the same thing at a fraction of the cost. I highly recommend!

I am not a carpenter. I don't make things to sell, so I have no basis to judge this in terms of a professional. But for someone who can't rip straight with a circular saw, and is slightly afraid of a table saw, this was the perfect solution. I needed to rip several 4x8 sheets of plywood into 3" strips. This was the exact right set up. Instructions are good. Easy to follow. My amateur Ryobi circular saw fit into the guide and off we went. Very pleased with this purchase

Worth the hype. We are thrilled at how well this works and has become a critical part of our construction toolkit. Awesome for when you dont have easy access to a table saw

Craig always knocks it down at the park and it was cheap enough.Not to break the bank. just mount your favorite saw to it.And get a perfect cut every time.

Very cheap and flimsy. Doesnt cut accurately. The track is made from aluminum which is great, very straight and accurate. But kreg uses cheap blue plastic pieces in a lot of their jigs which are inappropriate for woodworking. In this case, the sled is plastic. And the set screws bend the plastic sled if they're tightened enough to hold the saw in place. The result is that the saw blade doesnt stay in the exact same spot, even between cuts. This jig relies on blue strips of plastic to achieve zero clearance surface protection for making clean cuts, and for ease of lining it up with your mark. But one the saw has slid out of place due to the cheap plastic material the sled is made out of, the saw eats away the plastic zero clearance strip and the jig is no longer zero clearance. I was very careful to try avoiding this, but clearly not careful enough, and the jig already requires replacement strips after 20 cuts. I feel like this sled will break very easily at some point as well. Kreg needs to make the sled out of aluminum if they want to develop a reputation for quality American made tools.

Works great love it easy to put together easy to use. The only issue I had is just for the type of thought I have it doesn’t clamp 100% perfect onto the slider just because of the type of base it has but other than that I think it’ll be fine with any other saw it could have adjustable arms a bit longer for the type of saw I have so I clamps it better

Had quite a few 4 x 8 ft sheets of OSB to cut up, and this made it much easier and a lot more accurate. My Evolution circular saw fitted perfectly. Nice and easy to set up and use.

自作も含めいろんなガイドを試しましたが、その度に満足のいかない結果に残念な思いをしてきました。 どんな道具にも使いこなすにはコツが必要で、しかしそれを習得する前に丸のこを使うのが億劫になっていました。 ところがこのアキュカットは、そんな私でも一発でコンパネの長挽きに成功。丸のこを使うのが楽しくなりました。 唯一越えるべきハードルは、説明書が英文だということ。でもそれはスマホに入力すれば和訳してくれます。そうやって地道に説明文と向きあうことで、より商品が理解できるというもの。 おすすめです。

Super produit très utiles et rapide à monter expédition plus vite que prévue content en tout je le recommande

El material es de muy buena calidad Solo que a mi no me quedan derechos los cortes