Ingersoll Rand 114GCQ EDGE Series 2 5/8" Stroke Air Hammer Kit | Includes 3 chisel attachments, 3,500 BPM max, ideal for exhaust system repairs and general maintenance tasks

Quick delivery overnight helped me to continue working on my ancient trailer that I am rebuilding. Purchased the trailer from Home Depot back in the early 90’s and worked well for our needs. Cost ratio is good and the zip gun as we call it around here worked incredibly well. My old one would not provide enough force to break over a dozen carriage bolts that were rusted. This did! The chisels with this are good and not too light. I purchased a different set to use with this gun and the metal chisels were all too soft so went back and used the chisels that came along with the gun and worked well. As another reviewer pointed out, make sure you add pneumatic gun which would help the gun work properly. I had some oil but couldn’t find it and I think it would have worked much better if I oiled it first.

This air hammer worked perfectly for my application. Just make sure to oil it through the air inlet before using it. Others have provided valuable and relevant performance information so I won't cover the same information. However, the one item that is missing in the reviews is how to remove the plastic safety tag installed on the air inlet. I have included a photo of the plastic safety tag. You can see that the tag is composed of an outer shell, a flat keeper plate with two plastic nubs, and a plastic bolt that screws into the air inlet. To unscrew the plastic bolt from the air inlet you will need to dissassemble the tag by pressing on the two plastic nubs that extend through the rear plastic shell with a pair of pliers, or simply cut the nubs off with a pair of dykes. This will allow you to separate the plastic shell from the plastic keeper, thus exposing the plastic bolt. Once the plastic bolt is exposed simply use a socket to remove the bolt from the air inlet. - As I have already stated, this is a solid and reliable impact hammer and I would recommend it to anyone needing an air hammer.

Excellent tool

I bought this because I'm cheap. I needed to remove tiles from my kitchen walls during a renovation. I looked at SDS Hammer drills. They are really expensive. I wasn't going to do this by hand though. This looked like a decent substitution, and it was. I was able to take all the tile and mortar off of the walls with relative ease. What I like about this tool: It's easy to switch chisels. The quick release is slick, sometimes too slick as I accidentally released the chisel a couple times while working. The weight; it feels solid, and is solid, with out being really heavy and tiring. Reliability and ruggedness both seem good as well. I used this for 40+ hours so far in a dusty environment. I drop some IR oil into it every day before use, and I've had no problems. I've dropped it a few times as well, still no problems. What I don't like: The rubber grip; it slides around during prolonged use, to the point of catching the trigger and keeping the tool running. The clamping mechanism on the quick release - it took me a couple times of going back to my tools and tightening it ever more to keep the piece from rotating off. I got it now, but it was annoying. All in all, it's a great too for tile removal, and whatever else you may need it for. Especially at this price. Keep in mind you need a decent air compressor. This uses 4.0 scfm, so I ended up having to get a new compressor, so this eventually was the same price as an SDS Hammer drill.

I’ve been using this Ingersoll Rand 114GQC air hammer and it’s been solid. Plenty of power for stubborn bolts, exhaust work, and general shop use. The quick-change feature is a big plus makes swapping bits fast and easy without slowing you down. Build quality feels durable and it holds up well under regular use. Definitely a great tool for both DIY and professional work. Would buy again.

In the Product Information Manual under Warning (Pages 2 and 3) stipulate: 1. Put 6 cubic cm (6 ml) of solvent in the air inlet and operate the tool for 15 seconds. I used break cleaner. 2. Then put 3 cubic cm (3 ml) of Ingersol-Rand #10 oil into the air inlet and operate for 5 seconds. Note: a. You must hold the trigger all the way down while you put in the solvent and oil or the inlet will not accept the 6 cubic cm’s of solvent or the 3 cubic cm’s of oil. b. You can use a rag or folded paper towel held tightly over the discharge opening of the gun or it will not operate and the solvent or oil will not work its way through the gun. I wore an apron because the spray/mist will blast out. 3. Quick Change Retainer: a. First install the quick-change retainer onto the gun and torque for 4 lb. ft. I used a 3/4-inch internal pipe wrench/grip extractor with the appropriate attachments so the 1/4-inch torque wrench could be used. b. Then tighten the 3 Allen set screws to 9 lb. in’s. Go around in the retainer keeping track that the amount of exposed threads for each set screw is the same until the torque for each set screw reaches 9 lb. in's. I used a digital torque wrench (1/4’ drive) and a 3 mm hex bit socket. 4. Done – ready for use. The gun works great for my application – automotive. I use the SUNEX TOOL Air Hammer Chisel and Separator Set

This air hammer worked great. I used it to remove bushings from some leaf springs on a 39 Plymouth and it did the job easily. I cut thru the bushings from end to end then folded up the edges. Then put it against an edge and drove it straight out. The bushings didn’t have a chance. Before I used the tool I read the instructions and they said that the tool was coated with an anti- rust compound both inside and out. Use a suitable cleaner to remove then oil before using. Then plug in and operate for 5 seconds. Then pour oil in it and operate for 15 seconds. I have no idea what a suitable cleaner would be. I thought about mineral spirits but decided to use carburetor cleaner in a spray can. Stuck the red straw down the air supply hole and filled it up. Squeezed the trigger, filled with oil and ran it again. I used Kobalt air tool oil from Lowes. I was somewhat concerned because reading questions and answers concerning air compressor CFM it seemed this tool needed 90psi with 20 CFM under load, 4 CFM with no load. My compressor is 1.9 hp, 27 gal that puts out 5.8 CFM at 90psi. I’ve included a pic of it. I had no problems, the tool worked just fine. I use a drier system on my airline so I have 2 regulaters. One at the compressor I set for 110 psi. Coming from the drier I set at 80psi while squeezing the trigger of the tool. When I put it to the bushings, it went thru them like melted butter. This tool really saved me a lot of time and headache. I’m glad I decided to try even with my concerns.

Best tool from the best air tool company at this price! Who are you kidding. If you ever see a quick change Ingersoll Rand tool at this price buy it. So far we have two in the shop, probably going to add another soon.

Propaganda enganosa! Não cumpre o que promete, dinheiro jogado fora, não sei como uma empresa de nome lança um produto que não funciona mesmo com a mangueira de alta vazão não consegue cortar um simples pino de aço.

I like the product but it take time for delivery

Perfect for the job. Nice quality build & easy on the hand. Unfortunately, one didn't stand up too well & corroded after just 3 days of use. Photo #2 shows the worst one, after just 3 days use underground:(

everything is fine

Great tool excellent price