Nilight TR-04 Truck Tailgate Bar 60" Triple Row 504 LED Strip with Red Brake White Reverse Sequential Amber Turning Signals Strobe Lights，2 Years Warranty

Was a breeze to install. I didnt want to use the 4 pin and occupy my trailer harness so i cut that off the light and hardwired it in. This doesnt void the warranty as the manufacturer instructs you to do so on the instructions included if the harness doesnt fit. Took me about 1 hour but its not my first time. Very bright. Comes with some clip hardware to secure but i didnt want to screw anything so i picked up additional ziptie mounts as a backup to the adhesive strip on the lights. Make sure to use alcohol and clean where you plan to stick it and a warm day or heat gun is best for adhesion. Once you push it on it felt really stuck. I'll update when it fails but was just installed today.

First Day Review: I bought the 3 row, 60" strips a few weeks back and just installed them last night on my 2016 F150 XLT Super Crew. I liked them so far. Here are some thoughts:- 4-pin Trailer Harness:Before installing anything, I wanted to test out the 4pin harness connection. I opened the box that the LEDs came in and pugged them right into my 4 pin trailer hookup. All the signals and LEDs worked, but there seemed to be a delay. For example, when the flashers were on, the amber lights on the LED strip would come on a split second too late and not finish before another blink was fired. It was off. Next, I drove around for about 20 minutes with the trailer connection and the LEDs in my bed. I kept receiving trailer connecting and trailer disconnected messages. So I did not use the 4pin harness.- Wiring:I did not use the 4pin connector and did not want to splice into the wires in the trailer hookup wiring. Instead, I spliced the wires at the driver's side backlights (for power, left blink, reverse and ground) and the passenger side (for right blinker). I ran new wires down to a central point near the driver's side. I had to do a few searches to find which color wire was what... but once I did it all came together easily. Not sure if this approach was best, but it worked for me.I will need to go back later and make sure the wiring is 100% watertight with some type of a junction box. And I need to add some protective plastic shielding where the wires touch metal. But I just wanted to get this done last night.- Installing the LED Strip:The strip comes wrapped around itself, in a small-ish box. When I was ready to install them on the truck they kept trying to roll back up... this made it tough to do (more about this below). If I was to do this again I would have laid them out for a few hours (or overnight) so they flatten out.Before installing I cleaned the bed thoroughly with soap/water, a degreaser, and made sure it was dry. Once clean I used took time to center the strip and placing a small piece of electrical tape onto the bed of the truck and the strip to know where the center point is in case it moved.I started on the side of the drive, peeling off a little tape. I applied a bead of rtv silicone adhesive to the bed and pushed the stip against the bed, holding it there for a minute or 2. I worked my way across the bed, ensuring it was lined up/even with the bottom of the tailgate (where I thought it looked best.I had some issues with the beginning of the strip pulling up by the time I go to the end. And then I had issues with the end once I went back to the beginning. I ended up jamming a roll of electrical tape on both ends for an hour or so to ensure it stayed.- Overall:They are super bright. That is both awesome and might be weird. Awesome for more visibility to bad drivers around me. And being able to back up with more light is great. Weird because of them just being too obnoxious. If someone in the car behind me is blinded, that sucks. I may need to have a buddy drive the truck while I drive a car to see.Again I dig these so far. I will update with pictures and more thoughts as I have them.

This works great! Better visibility in inclement weather. The lights work as promised and are easy to install. I bought an installation kit to hard wire into the existing lighting and had my truck service shop do the install when I did normal scheduled maintenance. The tech was as impressed as I am. The adhesive has not come undone in hot weather and seems well affixed during winter. On the mountain roads with blind curves, drivers behind me are able to see my lights reflecting in the snow and know I am ahead, just around the bend. The amber turn indicators are well visible. The double row of white reverse lights are unmistakable in broad daylight. Backing out of parking stalls is easier because there is absolutely no way other drivers to not see the lights. The lights look like they belong there and not like some "Hokey" add-on. I am pleased.

I installed this on the back of my enclosed trailer so I had to cut off the 4way plug which isn't a big deal. The wires are really thin gauge (I would like to of seen something a bit heavier gauge) so just use the right wire strippers. My main concern is the blinkers and Hazzard lights are amber! This is my fault for not paying attention to the listing description. Red or amber are both legal rear turn signal colors in the US, I just really prefer red. Time will tell how long it last but so far it works as it should. I also wired the backup light to my interior lights to light up my rear ramp at night for loading and unloading. (I didn't feel like running a wire the length of my trailer for a back up light).4 stars due to amber turn signals

Easy application just peel and stick. I used two of them, one on each side of the back of my RV for higher visibility brake and turn signals. Wired both sides of each light bar’s turn signal wires together and the turn signal runs full length on each side! BIG improvement in visibility and road safety!Massive improvement over the little tail/brake lights originally on my camper!

I bought these strips for my 2021 Ram truck and I was disappointed when I saw that you had to use your 4 pin connector to make these work. 1st problem is that it is not a straight flat area under your tailgate to make them stick, you will have a wavy strip and your lights will not look straight. 2nd issue is that you have to tape it with the wires starting from driver side making it unable to reach your 4 pin connector. I will not splice my wire in my tail lights because then you risk possibilities in getting error codes in your truck if the ecm detects a voltage drop in your wiring. 3rd is that the white reverse light only worked for less than one hour then stopped working. 4th the lights do have a small delay when you turn your signals on, I could deal with that. 5th problem was, and not so bad, that you do have to unroll it and let it sit out for a day so it won't keep rolling back up on you. They do provide small plastic staples that you can screw into your truck to hold them down, but then you risk your truck to start rusting out at some point. 6th was a shipping issue, it stated that if I ordered within the 6 hour clock frame that was ticking, that I would recieve them the same day, lie, it arrived 2 days later.The only thing I did like about these lights was that they are super bright and at night you can see them well. It is a shame they can't make it plug and play into your tail lights with water proof connectors. I sent mines back the next day for a refund.

They work great.

Super bright, easy to install.Love it!This size is perfect for a full size pickup.Installed in less than 30 minutes on. Chevy Silverado.

This product is awesome , lights all work on a different LED line so brake lights and signal lights work when used at same time. Four way flashers are very impressive amazing to look at. Running lights stay on when lights are on, and back up lights are so bright you can see long distances when using it. It also customizes the vehicle you have them on. This product is well worth the money. Highly recommend this product. When you receive it in the mail you will receive these items: 1 heavy duty light strip 60 inches long , 3 clips with screws , and the plug and play wire set. Also the adhesive on the LED strip has a very strong holding strength , I give this product a strong 10 out of 10. Well worth paying the extra money as you do receive a heavy duty set. AWESOME PRODUCT.

Super bright LED's/ like sequencing turn signals/no instructions to connect to wiring only plug into truck trailer socket leaving an exposed wiring connection/should be hidden in brake lights compartment. Cliff

Very easy to install, very bright.Did the mount on the bottom of the tail gate rather then under it..As we transport rocks and soil and they get stuck under the tail gate when unloading, they would crush the LED light bar if mounted in the standard position.Will buy another one for the trailer...Update, the right side turning signal just stopped working, will ask for replacement...That said the lights are great and bright when they work...

What a great light strip….covers rear end of GMC Sierra Crew Cab 2018 and plugged into the trailer lights with an adapter…..if you use the 7-way outlet, use a 5-way adapter and you can use pin 5 for the reverse light ….small expense to avoid cutting wires in my Denali Pickup truck….the adapter can be found on Amazon as a 5-way and 4-way 7 pin trailer harness adapter. Do not install light according to enclosed diagram and parts…or you may inadvertently put a screw through the wiring of the device. Great lights, very responsive and improves vehicle safety immensely…..the white reverse lights are amazingly bright as well. Great job.

I just finally got these installed in April, it was warm enough to put them on my truck, very easy to install but they only lasted 2 months and burnt out!So not happy how long they lasted,But did look great on my truck for the time they worked