IF-10018-MBK 4 Pcs OE Style Wheel Fender Flares Compatible with 07-13 Silverado 1500 2500HD 3500HD 6.5 & 8.1Ft Fleetside Models, NOT Fit Dually Models with Crew Cab,Black

I'm not sure how they fit because I bought them to match some flares that were damaged and these weren't exactly what I was looking for so I returned them. But they look good. If I wasn't trying to match existing flares I certainly would've installed them.

1. These do not fit a 2013 GMC Sierra 2500HD Extended Cab 6.5' bed. No matter how hard I tried, these would not line up with the top edge of the wheel well without warping/deforming at the bottom corners. 2. There are no instructions on how to mount these or use the mounting hardware provided. Once I figured out the hardware, I realized it is completely ineffective. The clips slip off and the screws simply would not thread in. 3. The plastic quality is poor. During my attempt to install them, two of the flares cracked and "tore" along the inner edge. Overall poorly engineered and just does not fit the application it was advertised for.

But for a full-size Chevy Doesn’t fit very well big gap between the rich and the original fender edge they do give you spacers but not enough I had to make some of my own

Started with a passenger side fender front. That was pretty easy took out the 4 Factory bolts put the product in place reinstalled the bolts. Unfortunately either the holes in the fender cover or in the vehicle itself not properly spaced. After tightening the screws the plastic fender bowed away from the body at the corner closest to the door. The Simple Solution for me what's to remove the original bolts and replace them back into the original fender well and place the new Fender guard over them. And I simply hold down the plastic fender flare until the corner was flush and drove a self-tapping screw through the plastic of the fender flare into the plastic of the fender well. The driver side was it as bad but still flopped around easily so I repeated the procedure and was very happy with the results On the rear fender flares there are two Factory holes at the top of the fender well and the supplied Clips easily connect those. There are four more clips supplied but I ended up only using to her side because the two towards the bottom we're about an inch away from any metal. They would hold nothing in place. To correct this I crawled under the car and drilled a small hole through the plastic fender flare into the body of the have the truck fender. This might bother some people it didn't bother me heads it was under the car and would never be seen even where the fender flares to be removed. I knew going into this for the price point they're probably would be some Ingenuity involved in making them look the way I wanted. But for under $100 I hid the dent in my front fender without a trip to the body shop and $800 out of pocket.

Most likely received someones returned flares as there were smudges all over the difficult to fit rear and appears previous owner sent back. No instructions, a bag full of 4 types of screws, plastic and metal and couldn’t use a single one. Front flares were quick install using factory wheel liner bolts but have gaps at each top corner but rears are difficult to install. I used self tappers and started top center then stretch and pull down to get one on each bottom corner. Would not recommend if you want to put on a nice truck, mine went on a pos farm truck so gave 3 stars since it looks better with then without and only $66 dollars

You get what you pay for, honestly for the price you can’t beat it. Easiest way to install is get you some self taps and just mount it up that way, since the holes won’t line up . If you need a cheap way to cover up some rust , these are it !

I dislike everything. The flares are really stiff, and not molded even close to the body lines of the truck. More importantly, they are about 2 inches too narrow for the wheel opening, so I had to shim them with old hex nuts just to get them on. Then they don’t sit flush against the bed so I had to load them with double sided tape and go around the front edge with RTV to hopefully keep the wind from ripping them off. Total trash, zero stars, don’t waste your money. There’s easier ways to hide the body rot

Very good product fairly easy to install. Chevrolet has an issue with rust at top of wheel openings. Was able to repair rust, then covered repair without having to refinish entire panel. I was skeptical at how flares were going to look. I’m pleasantly surprised how good they look. Other reviews stated difficult to install, and did not fit. I had no problems. Took out of box and left them lay for several days in warm area. Then did the install👍👍

Does not fit to my car

Yeah the back takes up some decal but don’t be discouraged by the add indicating it doesn’t fit a 07-13 2500 long box..they do. AND for a reasonable price. Fitting them is no easy task but, it’s not like they’re made of sheet metal. I had to customize this install a bit having lost some inner structure but these are ridged enough to add fasteners where you might need them to make up for that. Buy these..not the $600 + option. I think it’s ridiculous these after market company’s are trying to cash in on these trucks..

Perfectas!!!! Super recomendadas

They work okay. For what you pay they are pretty good. The installation requires no modification (drilling holes etc) so that's a bonus for a quick fix. They also don't stick out much so the truck still looks normal with regular size tires. The plastic is a bit flimsy and over time there seem to be spots where it sticks out a bit away from the body (I noticed that the most on the front fenders) but it's not super noticeable. I managed to pinch one of them on the rear fender on a garage door frame and bent my fender in yet this piece didn't crack or fall apart so the flexibility of the material was beneficial in this instance. Not a big fan of the metal clips that are used to secure parts of the rear flares and the seem to be rusting and will eventually break (one already did) due to the thin metal, but this is can be fixed/changed/adjusted with a bit of tinkering. Can't go wrong with this product if you're looking for some cheap and quick over fenders that don't require drilling/riveting.

لم يتم التواصل معي لارجاع المنتج ولا اعرف لماذا هذا التصرف ؟؟