eSUN PLA+ 3D Printing Filament 1.75mm, Enhanced Toughness,1KG(2.2LBS),Black

Great filament that ran through the machine and printed smoothly. A good finish and did not peel from the bed or cause any issues.

Filament works well. Good adhesion and few failed prints. Strength seems ok. I've had problems in the past with pla filament that breaks in storage if placed under any strain, e.g. if you thread the end through holes in the spool to stop it unwinding. This pla+ seems to behave better. Just adding that I'm kinda sceptical about the reports of tangling being the fault of the filament. If you're going hunting for the end each time you take the spool out then you're potentially heading for tangles. If you keep close track of the and make sure it doesn't get tucked under other coils on the spool then there's little chance of a tangle.

I’ve been using the eSUN PLA+ Bone White filament for several projects, and it consistently delivers smooth, clean prints. The dimensional accuracy is spot-on, so layers align perfectly and parts fit together as intended. It’s tougher than standard PLA, reducing breakage during handling, and it feeds through my printer without any jams. Overall, excellent for both hobbyists and more detailed 3D printing projects. Pros: Enhanced toughness reduces snapping and warping Dimensional accuracy of ±0.03mm ensures precise prints Smooth, consistent extrusion Works well with a variety of 3D printers Good color consistency (Bone White is nice and even) Cons: Slightly more expensive than standard PLA Some stringing can occur at higher print speeds (common with PLA+) Requires proper drying if left open to avoid moisture issues

Overall, I found it to be a good quality material. The white color of the filament was especially nice and produced clean and crisp prints. However, I did experience a few issues with the filament. At times, the material would get stuck, and I had trouble getting the roll to spin properly. This was frustrating and caused delays in my printing process. Additionally, I noticed that the color of the filament changed when it became too hot, resulting in a brownish color appearing. This was a bit disappointing, as it affected the overall appearance of my prints. Despite these issues, I still believe that the PLA+ Filament 1.75mm is a good option for those looking for a reliable and affordable filament. The white color is particularly impressive, and the material produces clean prints when it is working correctly. However, it is important to keep in mind the potential issues with the material getting stuck and the color changing when it becomes too hot.

eSun PLA+ became my go-to filament the first time I ever used it. Honestly don't have a bad word to say about it. Temp range is forgiving, it will give you great prints within a range of 15-20 degrees, so no need to super fine tune it. I've never once had a spool tangle on me. Layer adhesion is perfect, bed adhesion is great (as long as you're not doing anything silly). I must have put 30 spools of this in various colours through my CR6 and never once had a problem (atleast not one cause by the filament). I don't even bother waiting for a heat up or first layer anymore. Just hit print and walk away, full faith that this filament will print perfectly. Finishing is a bit trickier, but no more than any other PLA filaments, the + does give prints a stronger feel, but doesn't really make it much easier to sand, but if you know what you're getting into with finishing PLA prints, there will be no surprises with this one. Use it, love it, buy more. Not much more to say than that!

I have used many brands of filament but I always come back to eSun as their range is amazing. A wide array of colours and consistency across the range. This filament is flawless and prints well every single time. Whether you are printing drafts or a finished piece you always get a great finish with this filament. Perfect layer adhesion and excellent bed adhesion too. If you are looking for a filament that looks great and is a great price then this is the one for you! Bonus tip... if you ever find your filament has poor bed adhesion then bake your filament to remove as much moisture as possible. You can either bake it low and slow in your home oven or for an even better option, that won't annoy the wife, I highly recommend a filament dryer. They do really work!

Unfortunately very brittle so always breaks and blocks the filament tube

If you want a reasonably priced, high performing, low issue filament then look no further. I've been printing for three years and in that time I've only had three tangled reels and no quality issues. The layer adhesion is fantastic and it's very tough stuff for PLA. Just buy it, it's very hassle free and as you can see from the picture you can do anything with it. I've got reels over two years old and they still print like day one, you just have to store them right.

Excelent... Print ok... machine ok... Only apply the write setting

Excelente, sin ningun problema hasta ahora con mis impresiones lo volveria a comprar

Works a little bit less good than bambu lab pla but that is expected with the a1 mini. Is cheap for it's quality!

色も強度も問題なし。最近フィラメントの巻止め方が明らかに改善された。

Amazing filament, layer-adhesion is very good, very stiff and weirdly enough for a non specialty and/or fibre filament, layerlines are almost invisible. Its a beautiful off white color, a little bit opaque when not printed with full infill.