358 Ultra Probe with High-Heat 40" Silicone Cord

Replaced my non working cord perfectly and improved from older probe. The Polder base thermometer was still working, I am thrilled to keep using it now with the replacement probe. Longer cord, silicone base much improved.

I bought this probe to use with a Taylor oven temperature probe (the Taylor probe quit working due to abuse). It is not sold for the Taylor models, and I wasn't sure that it would work, but a probe is cheaper that the whole device, so I figured it was worth a try. Results: It works well, but you have to add 68° to the reading to get the correct temperature. I calibrated it against an instant-read thermometer in water from freezing to boiling, and there is a simple linear relationship. At temperatures below 120 (real temp) the display reads "Lo", but then is accurate (with the formula) up to at least 212° F (boiling water reads as 144° on the display). I have used it for several months now, testing it against an instant-read when the food is ready (every thing from tenderloin (display 62 = real 130), to turkey (display 112 = real 180), to bread (display 137 = real 205)), and the formula holds up. The probe itself has a nice length, and the wire attachment to the plug and and the thermometer end is strong. The handle on the probe is nicely designed and easy to use, even when inserting it into food in a hot oven. I keep a little table of readings next to the oven, so I don't have to think too hard while cooking, and I put a sticker on the display to remind me (or any visitors who use my kitchen). If you don't mind that inconvenience, it is a great replacement probe for the Taylor. I assume it works well with the correct (Polder) unit, too, without requiring the math.

Been looking for a replacement probe for about two years now could never find one to give accurate temperature either off by 100° or cable connection, too short or too long, after plug in it immediately went to the temperature in the house, tested it in hot water then the cold water give the same temperature up or down 1° as the other thermometers as we all know, these kitchen thermometers not very accurate and that is good enough for barbecuing or roasting a turkey

Fits and works as a replacement probe for my Polder digital cooking thermometer. BUT, the probe does have a plastic piece that will melt (but no completely) when used in the broiler. The plastic "grip" shows signs of melting but it's still usable and is in one piece. Not a big problem. However, when I received the probe, there were no instructions or warning to its vulnerability to high temps. Haven't tried it in the oven at, say, 400 degrees, but hopefully no further melting will occur.

I have had my Polder meat thermometer for over ten years now, and have had to replace the probe with this new model. I see that they have solved a design problem by adding a rigid plastic connection between the wire and the metal probe. The old probe just had the wire crimped into the end of the metal probe and from the get-go that looked like a weak link in the product to me. Eventually after may removals from a Boston butt using a thick mitt, I must have finally broken the wire loose at that joint and the thermometer didn't work right. The price of the new probe approaches 2/3 the cost of a whole new thermometer, but I liked my old thermometer and ordered this replacement. I plugged it in and turned it on in my home office where I have a digital thermometer. After about a minute of acclimation, both thermometers read the same. I am pleased with this replacement and think it will last a long time since they have changed the design.

I've gone through several Polder probes in the past two years. They always failed due to the very poor construction of the wire connection into the metal probe. This was a weak point that always shorted out after a few uses rendering the Polder thermometer useless. It's unavoidable that there will be some twisting and flexing of the wire and probe when placing a roast or turkey into the oven. I always had a spare on hand anticipating failures during Thanksgiving or a holiday. The new design is a vast improvement. The silicone support not only provides an insulated place to remove the probe when hot, but firmly supports the wire connection into the probe. 10 times into the oven and works like brand new. Out of habit I ordered two probes. With the improved design each one should last for quite a while. Never hurts to have a spare on hand. Polder finally got got it right.

This is a replacement for the polder. My old one got burnt up. This works great for my old Polder

Replaced the old one we had. Great fit and works perfectly

Needed as a replacement, works as expected.

Having used a Polder probe for two years it then stopped working, so I replaced it with a Polder Ultra Probe, which appears to be of better quality and works well. Time will tell on longevity.

The probe is working really well. It is a sturdier version than my old one so I expect a lifetime of perfect roasts

The item came quickly and fits perfectly to my existing probe.

This probe fits my meat thermometer and is a better design then the one it replaced whose wire snapped somewhere at where it joins on. Thinking this one will last longer.