Mazda Carplay and Android Auto Retrofit Kit, TK78-66-9U0C OEM Hub Fits to MZD Connect System, Apple Carplay Adapter Compatible with Mazda 2/3/6/CX3/CX5/CX9/MX5 2015-2020 Year(2024 New Upgraded)

Works flawlessly. Integrates seamlessly with the factory head unit like an original Mazda part. No lag, perfect fit, and easy installation. Highly recommend for adding CarPlay/Android Auto to your Mazda3.

I was a little nervous about attempting to install this, but the process went smoothly. There are many tutorials on Youtube to guide you. The hardest part was removing the old unit, which is held in place by clips that are difficult to manipulate due to the constricted space. I would recommend using a butter knife or flathead screwdriver to hold the clips down. I would also buy a trim remover tool, as I put a scratch on my dashboard. Once installed, the unit works perfectly. There is some lag once you start the car, but this is part of the software design and not a huge issue. Also, sometimes CarPlay will cut out and stop working, but I suspect this is a phone issue and not a problem with the unit.

This gave me carplay functionality in my 2015 Mazda 3 i GT. Installation will be basically identical with any of these, which is to say not too difficult. I've had it a few weeks now and have no complaints that could be the fault of this unit. Some installation advice if you get this: Don't disregard the foam pads you get. I noticed a bit of rattling near the shifter, even though it was zip-tied to other wires, and had to remove that part of the trim again to use the foam on them. Spend a minute or two flattening out one of the cables, just ~2 feet, or alternatively use a different cable all together. Feeding the wire from the nav unit down to the footwell genuinely was the hardest part. You can tie the other cable to the flat one once you've routed it through and pull it down further. Take your time, get an $8 trim removal kit, and enjoy saving a ton of money.

Worked great in my 2017 Mazda CX-5 (after upgrading the firmware). Instructions do not come with it so I had to look up a YouTube video but after about 2 hours I was able to connect my Android phone to the heads up display. I wish the wires were a little longer (In the youtube video the guy had a lot of extra wire; this kit was exactly the right length) and that more foam tape was included (I had to use some extra foam tape I had lying around) but overall a good purchase for my car.

Best purchase from Amazon ever! 70 bucks for this thing, then a $120 install from Best Buy, so for ~$200, I’ve got CarPlay plus new USB ports that power up my dash cam. The old USB ports had a trickle charge and wouldn’t even power up my dash cam. You will need to upgrade your firmware. For that go to YouTube and search for instruction vids by Killobyte. He also has one to change your settings to allow touchscreen functionality while driving, which comes in handy when using CarPlay. The connectivity to CarPlay is fast / instant once you plug in the USB cable (unlike some of my other vehicles), it works great and I am super happy with this. The technician at Best Buy said that it was easy to set up, and as far as fit is concerned, it fits exactly where the old USB module was located so I would say the fit is perfect. Now I can get rid of my cell phone mount and also the battery pack that I used to power up my dash cam.

I installed this last week. So far it has worked great. Picks up the device and auto starts android auto. The touch screen does not work while using android auto. I assume that is a limitation of the mazda unit as my touchscreen works fine outside of android auto. There are lots of videos on YouTube showing the fast/hack way to remove the device. My unit still worked and I didn't want to destroy it or my dash so I opted for the correct way to get it out. Deconstructing the center console. See the youtube channel "gear gadget experiments" if you have a mazda 3. Overall it wasn't too difficult. It took about 1.5-2 hours because I took my time and was very cautious not to break clips. This was my first time doing anything like this. Everything snapped back together and I don't have any rattles or loose pieces.

Received the product and had the Mazda dealer upgrade the firmware to v74.--- (2016 Mazda CX-5). Installed the module (videos on YouTube helped), but instructions for connecting wires were included. During install, I did ensure to properly and fully seat every connection. The CarPlay connectivity worked the day of install and the next day. When the car was used a few days later, there is now no CarPlay Connectivity. It will not recognize the iphone when it is connected. Have tried multiple troubleshooting tips: Soft reset of infotainment system, new USB cable, Restarted iphone, removed Mazda from the CarPlay list on phone, turned car off and let it sit away from the key fob to let it fully power down, etc. This USB module will not recognize the iphone when attached. Next step is to try another iphone and then perhaps will pull the Negative post cable on the battery to fully power down the car. Will see if these help. Hard to recommend this, if the reliability is this unknown. Will hope to hear from the seller on any other ideas they may have to get it working.

Works great, can confirm that I have installed two of these already on a Mazda 3 and a Mazda 6. No issues whatsoever with either install. I just wish it was easier to find install instructions or videos for specific car models.

Just installed this in my Mazda 3 2016 and works flawless! Great product, just check YouTube for the installation guide!

Lieferumfang: - 2 Kabel, die vom Display durch die Verkleidung zum USB Hub verlegt werden müssen - der USB Hub - 9 Kabelbinder - 20 Stücke Schaumstofftape, jeweils 100mmx30mm Einbau: Schwierigkeit einfach bis mittel, ca 1h ohne das Softwareupdate. Es musste nur eine Schraube (10mm Außensechskant), mit der das Display zusätzlich befestigt ist, gelöst werden. Der Rest sind Steckverbindungen, die man vorsichtig aber mit beherzter Kraft problemlos lösen kann. Der Raum hinter dem Display ist sehr eng, die Kabel zu verlegen eine kleine Herausforderung. Geht auf jeden Fall von oben nach unten vor, von unten eine Öffnung zu finden ist praktisch unmöglich. Die Anschlüsse sind zwar selbsterklärend und unmöglich falsch zu verkabeln, einem sollte aber vor dem Verlegen genau klar sein, welcher Stecker auf welche Seite gehört. Das Schaumstofftape reicht um (fast) die gesamten Kabel zu polstern. Ein oder zwei Stücke übrig zu lassen, um die alten Stecker gegen Rattern abzukleben, macht Sinn, weil man das alte Kabel am Kabelbaum lässt. Software: ACHTUNG! Die Firmware der "Head Unit" (des Displays und seinem Computer) muss mindestens Version 70.00.100A oder höher sein BEVOR man den neuen Hub einbaut. (Kann man unter Einstellungen->System->Über->Version Information nachsehen) Nochmal ACHTUNG: Führt ein notwendiges Update auf keinen Fall nach der beilegten Anleitung durch! Das kann die Unit komplett unbrauchbar machen. Wer das generelle Risiko eingehen möchte, kann jedoch auf eine 9-seitige bebilderte Anleitung, die im Internet kursiert, zurückgreifen, der haargenau gefolgt werden sollte. Bei mir hat es ohne Probleme geklappt. Bisher nur Android Auto getestet. Es läuft flüssig und tut was es soll. Fazit: Wer nicht zwei linke Hände oder große Angst davor hat, etwas kaputt zu machen, kann den Einbau locker selbst machen. Apple Carplay und Android Auto sind deutlich moderner als Mazda Connect und bessere Navigation als mit Google Maps findet man 2024 nicht.

Unidad perfecta para mi Mazda 3 MK3. Incluye la esponja para aislar los cables y las instrucciones. A tener en cuenta que la versión de firmware del coche tiene que ser 70.xx o superior. Funciona perfectamente en estas semanas de uso.

Very good.

I recently installed the Mazda CarPlay and Android Auto Retrofit Kit in my 2017 CX-5, and I’m very happy with the upgrade. The setup was straightforward—I had minimal trouble swapping out my old unit for the new one. If you’re considering the installation, I recommend watching a YouTube tutorial first, as it makes the process even easier. The system integrates seamlessly with the built-in screen and infotainment, and you can switch between them simply by pressing and holding the home button. I use a Google Pixel, so I can’t speak much for CarPlay, but Android Auto has worked flawlessly. For an even better experience, I highly recommend pairing this kit with an AAWireless dongle, which allows wireless Android Auto. One important tip: make sure your firmware is updated on the original unit before swapping to the new one. Overall, this has been a smooth, worthwhile upgrade and I would highly recommend it.