Manual Wire Stripping Machine Gauge Wire 0.06-1 inches,Scrapping Copper Wire Peeler Machine,Drill Powered Hand Crank Wire Stripper Tool for Scrap Copper Recycling

I bought a manual/drill driven wire stripper. I really love the ease and effortlessly way it strips wires. It is so much faster than stripping with a razor knife. Im a scrapper, and buying this machine has trippled the amount of money I get at the scrap yard. Paid for itself on the first trip to sell my copper. It is very well made, using quality materials. I would but it again for sure A+ 💕

This was an item I purchased for my brother. He loved it. Said it works exceptionally well. Strips the wire in record time.

Used this to strip a ton of wire. Worked flawlessly from the smallest to the largest wire. An absolute time saver for sure! I included a picture of all the empty wire casings.

I have run hundreds of feet of all different kinds of wire through this stripper over the last few months and have found the strengths, weaknesses and some things I would change about the design. First, I bought this particular one over other cheaper, exact copies because this one showed it came with a spare blade. As it turns out, a spare blade is not included so right away I had a negative opinion of it and wished I had bought the cheapest one of this style but it has done the job so far on a single blade so the blade life is pretty good. I have stripped solid wire, stranded wire, aluminum wire, romex, automotive battery cable, multi-conductor wire and more styles. I have found some work better than others in this machine. Solid wire is the easiest to strip and stranded takes some dialing in of the cut depth and gets a bit messy but works good - wear gloves! Flat Romex can be stripped with this by using the largest hole to remove the outer cover then stepping down to the small holes for the individual wires inside. Wire with braided cloth-like jackets (old style wire) does not work as well and will clog up the wheels so the machine has to be constantly cleaned, I use a pick. A cordless drill makes stripping wire very easy, I never even installed the handle. I also keep a cable cutter nearby and a razor blade for any missed cuts or cuts that didn't go deep enough or just cutting off excess insulation already stripped off. A pick cleans out the drive wheels when they get clogged up (see photo of gunk on wheels). I do have problems every so often of the drive wheel slipping sideways on the shaft and have to put it back in place with a small prybar and re-tighten the set screw. Lastly, this machine should come with thumb screws instead of bolts to make changing the wire feed size plate a quicker operation as I find myself changing it fairly often. If you use the largest hole, the plate needs to be removed completely and flipped around. When my local scrap prices are about a $3 difference/lb for stripped vs unstripped wire, this machine is a no-brainer and is a money maker worth buying and saving time.

works as intended. fair quality and it is easy to use.

I love this stripper for ROMAX and similar gauge wire. It is light, durable and good at stripping wires. I typically run 3 or 4 gauges through same setting with little difficulty. Easy to adjust up or down for larger/smaller gauges. My primary complaint is that the handle is so small that it makes it difficult to mount. I use the hand crank since it is almost as fast and doesn't cut into my bottom line. Electricity costs and so does wear and tear on a drill. The exercise doesn't hurt either. It is a breeze to set up. I am purchasing a 2nd one for aluminum wire since I do not want to dull the blade I use on copper on low value wire. I mounted mine on a large thick board that I just set on a table top or clamp down on a sawhorse and that works perfectly for me while allowing me to move it around to strip anywhere I want. One idea is if the handle were high enough on the hand crank side that I could mount in the center of the board rather than the edge. I can understand the drill side being low so as to fit a drill onto the board to power it.

Yes, it works very well. Thank you.

Absolute bargain. Very well made. Gears hold wire well with very smooth pulls and blade holds up well. Adjustments are easy to make. I’ve used it to strip miles of 10,12, and 6 awg insulated wire effortlessly.

Very nice product

Not in use worst product & amazon return process very late worst exp this order

1mm and below 1mm wires not working

Not working west product