BRCOVAN Anti-Theft Motorcycle Phone Mount Holder with Vibration Dampener

Fits Motorola android phone. Very stable. Several polymer pad sizes to fit the tube it is mounted on so that the clamp doesn't mar or scratch the tube. I placed it on my 2022 Indian Superchief Limited handlebar by guessing and then relocated it ehere it worked for me best and I couldn't tell it was mounted at my first spot. Suggest adjusting the main block part to fit your phone first by loosening those screws on the back and placing your phone into it and tightening the screws with the phone in it when it holds your phone as you would like it to (i.e., mine is off center to allow the phone charging and speaker output ports to be accessed). This sounds more involved than it is. Then place it on your tube (handle bar?) at where you think you might want it with the fasteners and clamps loosely holding it in place so that it can be moved about for the proper angles and such with your cell phone in it so that you can see how it fits for what you want first and then tighten the fasteners. Mine sits behind a windscreen but handled high freeway passing speed beautifully. They have a phone lock screw that sets the phone holder clamp itself. I use the bike's phone charge port over the front cylinder with a sturdy 3' long cable plugged into the phone and loosely tied around the frame at the bottom of the triple clamp and it keeps mine charged while giving my bike unobstructed handlebar movement. I've ridden in squalls at speed on the freeway without problems. To put the cell phone in ensure that the knurled hand tightened thumb screw is loose (it has a friction stop so you won't unscrew it all the way out and drop it to lose it on he ground), place the top of your phone under the upper cell phone holder and push the phone up (my cell phone has a thick drop protector but this holder is designed for that) and push he phone into the holder. The spring is strong enough to hold the phone securely but not break the screen. Then screw the knurled thumbscrew snug by hand, plug in your attachments (my charging cable) and you're ready to ride. Removing is doing the above procedure in reverse order. Takes longer to read than do. Very easy to install and even easier to insert and remove your cell phone. My Motorola is a rather large cell phone and it works well. The clamp and holder is not readily taken off the bike by design. It has a security fastener in the plastic handled clamp that is supported by a special Allen wrench that you tighten after you position the cell holder and tighten the angles you like with the plastic handled clamp so someone can't readily disassemble the phone holder and steal it when you aren't around. The cell phone is the only portable part by design. It seems well designed and well made for years of use. Eventually the plastic will likely fatigue but its built like a brick house and the knurled thumbscrew locks the phone ino the holder regardless of the rigidity of the springs. This model doesn't use spring force alone to keep the cell phone solidly installed in the phone clamp. That knurled screw locks the cell phone into the phone clamp.

What a great product. It adjusted perfectly in a Harley Road King 2009. No vibration at all! Great value, very sturdy and easy to use.

I'm impressed. It won't fit super thick phone cases as mine is a galaxy s26+ with a case that fits 5 cards and is about as thick as I'd want to get. It sits nice and high, easy to put on and it'll stay on at 90+mph. Takes 2 hands to get off but that's what you want. You can rotate for landscape as well.

I'm blown away by the quality of this product and the value. It is made of alloy overmolded with a grippy rubber like material on all areas that will contact a phone. The springs on the main clamp hold the phone VERY securely, and it has a lot of adjustable range. In addition, the side pins are adjustable for different width phones. They are fastened by screws so that you set them once, and you're done. On my Pixel 10 Pro, one of the pins does cover the down volume button. While adjustable for width, you cannot adjust them along the long edge of a phone. As stated in the instructions, you are meant to leave a small gap between the pins and the long edges of the phone. I used a business card as a shim, and set them that way. These pins are an additional piece of security as the main clamp is strong enough to hold the phone securely all alone. The bracket comes with multiple round shims for a variety of mounting bracket and handlebar sizes, and it also includes a mirror post mount. The clamp balls are coated in a soft, sticky material that allows the main clamp to grip very securely. I am confident that with these accessories that most any mounting situation can be accommodated. Once mounted, this thing isn't going anywhere. A rubber interface between the clamp and holder body does a decent job of absorbing high and medium frequency vibrations. As described, key fasteners are Torx anti-tamper screws. The kit comes with the necessary tools. For me; these will live in one of the small zip loc bags that come with it, and they'll be hidden in a pocket in my tank bag. All in all this is a great piece of equipment. It will be holding my phone for navigation on an upcoming trip around the Italian and Swiss Alps.

**Near the bottom of this review is a PRO INSTALLATION TIP** FIRST, the "unimportant stuff" - I have purchased 6 or 7 phone holders from different brands for my motorbike. Only one of them was good enough to be used on my bike for over 3 years. I'm changing my OEM mirrors on my motorbike to bar end mirrors. The last phone holder was installed with an L bracket directly under the mirror bolt. Although this phone holder is sold by BRCOVAN, The actual brand name is KEWIG. NOW, the important stuff" - "THE GOOD" - The packaging is very good. Everything is separated and doesn't come in one big bag like the inferior brands. As soon as I picked up the main body of the phone holder, it did feel pretty heavy, and very durable. Although it is made of plastic, like pretty much everything today, the plastic is a lot harder, a lot more dense than any other brand I've tried in the past. The handlebar installation was pretty simple and quick. All of the rubber inserts have raised edges that help align the handlebar insert with the bracket. Something I have never seen before. The insert and bracket themselves once installed do not move at all. The instructions are pretty clear. Not only do you get photo instructions, but you also get worded instructions. You will need a Phillips head screwdriver to adjust the side and lower grips on the main body of the phone holder. The grips themselves are made of rubber / silicone and are nice and soft. We will see how everything holds up in Florida weather. I only own a motorcycle, so I ride it every single day. Rain or shine. Installing the main body of the phone holder to the double socket arm was very difficult. Inserting one of the balls into the double socket arm was pretty easy. But once you have one ball inserted, the screw inside the twist lock on the double socket arm acts like a fulcrum. So the opposite end of the socket arm will close up a little bit. So don't waste your time trying to shove both balls into the double socket arm, until you read below. **PRO INSTALLATION TIP** There is an "anti-theft screw" on the double socket arm. Take this screw out completely. Then you can actually unscrew the twist lock a little more. Allowing both balls to be inserted into that double socket arm very easily. I have a Galaxy S24 Ultra with an OtterBox Commuter series phone case. The phone with the case is pretty thick, but it does fit very nicely with a little extra space all around. And the telescopic rods on top do hold the phone very securely. They do feel well-built. Also, there is a high speed secure twist lock on the top back of the phone holder near the telescoping rods. But honestly, I don't think you will ever use it. That's how secure my phone feels when inserted. The face of the KEWIG phone holder also has soft rubber / silicone panels. And they do feel really really nice. "THE BAD". Once you get the phone holder completely installed, inserting or retrieving your phone IS NOT a "quick one-handed access" as the product information states. If you do not hold the double socket arm when inserting or retrieving your phone, the positioning of the phone holder WILL MOVE. Even if it is just a little bit. But that really is a small thing to me, seeing how well made this phone holder is. Because most phones today do have two columns of camera lenses on the back of the phone, 1 telescopic rod will cover the innermost lenses on your phone. But for me, that really is not a big deal. Now for the vibration dampening. It is only marginally better. That's all I can say. But I don't really use my phone's video camera when I'm riding. So again, no big deal for me. All in all, I wished Amazon would allow us to give 1/2 stars, so I could give the KEWIG phone holder 4.5 stars. But since they don't, I will have to settle on 4 stars. If KEWIG could do a redesign of the double socket arm so it doesn't move and actually allow for a "quick one-handed access" and allow no blockage of some of the rear camera lenses on today's phones... This phone holder would no doubt be 5 stars from me.

I was cursing while installing this thing. You need tools. And it looks super bulky. However, once you managed to install, then you get it. I can safelt leave it in on my bike because it can't be removed easily. Stealing the bike would be easier than stealing this. And there is no way my phone is falling from this. Maybe after I hit a truck but still not sure. One last thing, it's pretty solid once you fixed it, find your angle and your phone will stay in that position forever.

This cell phone holder works great. I bought 3 of them. One for myself and for my husband and son, we all like it. They were easy to install, and very versatile. They will securely hold your phone in a vertical or horizontal position. Also and very important is: they actually fit phones with cases. You don’t have to remove your phone from its protective case to use this holder!!

This is extremely well built. Putting it together requires a bit of force, especially where the ball joints meets the pivot adapter. Don't worry, it won't break. Adjusting it was easy but if your phone is over 7" long, fitting the phone into the holder might require a bit of force but once installed, it won't go anywhere. The way it's designed allows you to easily adjust the angle of the phone.

Die Smartphone-Halterung macht einen sehr hochwertigen, robusten und soliden Eindruck. Sie ist relativ schwer, da sie hauptsächlich aus Metall (eloxiertes Aluminium) gefertigt ist. Sie hat an allen Kontaktstellen Gummieinsätze, so dass die Smartphones gegen Kratzer geschützt sind, nicht herum rutschen können und gut gehalten werden. Sie ist größer als man im ersten Moment denken würde, was jedoch nicht überrascht, da sie auch für große Smartphones gedacht ist. Sie nimmt mein Samsung S24 Ultra auch mit Schutzhülle problemlos auf und hält es zuverlässig. Ich habe sie am Motorradlenker montiert, wo sie hervorragend passt und auch die Sicht auf das Dashboard nicht stört. Für Fahrräder geht sie sicher auch, aber dafür erscheint sie mir doch etwas zu wuchtig. Die Vibrationsdämpfer sind hervorragend, so dass es keine Probleme mit Vibrationen oder Erschütterungen geben sollte. Die seitlichen Begrenzungsstifte kann man mit Schrauben an die Breite des Smartphones anpassen, sie lassen sich jedoch auch ganz entfernen, wenn sie stören. Ich denke zwar, dass die oberen und unteren Klammern (die einen Gummiüberzug haben) das Smartphone auch so sicher halten, wollte es jedoch nicht darauf an kommen lassen, da ich sie im Querformat nutze. Daher habe ich die seitlichen Begrenzungsstifte dran gelassen. Die Feder des oberen Haltebügels ist ziemlich fest, so dass man einen gewissen Kraftaufwand braucht, um das Smartphone einzusetzen und heraus zu holen. Dafür wird das Smartphone entsprechend gut gehalten. Man kann den Haltebügel auch noch mit einem Drehknopf auf der Rückseite fixieren, so dass er fest ist und nicht mehr bewegt werden kann. Dadurch kann auch niemand im vorbeigehen (z.B. an der Ampel) das Smartphone einfach herausnehmen und damit abhauen. Das schützt natürlich nicht vor Dieben, wenn man es unbeaufsichtigt (z.B. beim Tanken) stehen lässt. In solchen Fällen würde ich das Smartphone immer mitnehmen. Die Halterung lässt sich aufgrund des doppelten Kugelgelenks und des Verbindungsstücks sowohl senkrecht als auch waagerecht nutzen und in einem gewissen Rahmen nach oben, unten, vorne und hinten einstellen und drehen. Man hat damit einen recht ordentlichen Spielraum für die gewünschte Position. Die Schrauben zum fixieren der Manschette und des Verbindungsstücks sind Torx mit innenliegendem Stift. Sie bieten damit einen gewissen Schutz gegen Mitnahme der Halterung, da das kein so übliches Format ist (Werkzeug ist im Lieferumfang enthalten). Natürlich bietet das jeodoch keine absolute Sicherheit. Ich bin mit der Funktionalität und Qualität sehr zufrieden und kann die Halterung für Motorräder empfehlen.

Diminui em mais de 90% a vibração, permitindo até uma filmagem por ele. Super recomendo.

Recommend.

Using this product with Galaxy Fold 5, and it is great, the phone is secured while folded, and also made of a very good material and quality I recommend it for others

Esta perfecto Muy buen material tomando en cuenta que es nuevo Solo hay que ver si aguanta el sol y la lluvia por qué los colchonsitos que tiene para amortiguar son muy delgados pero por lo pronto está todo perfecto