21.53 SqFT 10mm Heat Shield Thermal Sound Insulation Proofing Deadener Mat Car Noise Control Acoustic Dampening Moistureproof Waterproof (40"X80")

My 1992 Grand Prix STE 5 speed, which I've owned now for 27 years, had a major oil leak years ago, that spattered all under the hood and pretty much destroyed the OEM hood heat blanket by oil soak. I had removed it decades ago and just had bare steel. After getting some other things taken care of that needed repairing, I wanted to drive the car more this year, but again noticed how much heat the 3400 DOHC engine put into the hood's sheetmetal and paint, not happy. So bought this heat absorbent matt. Put it on last Saturday, peeled the centre of the backing and adhered it to the hoods centreline, then worked outward toward both edges, came out looking quite nice, very pleased with the result. The glue is pretty much something, don't get it stuck to where you don't want it or the foam will rip as you attempt to remove it, I'm expecting after a few heat-cycles it should be bonded on like cement. Quite satisfied with the results, recommend without hesitations.

Good stuff at a decent price. Very sticky backside. I will be getting more of this for a van we are doing.

This foil backed sound deadener was easy to install. One reason for the 4 stars is because of the adhesive in some small areas coming off on the paper. You could re attach it to the mat no problem.

I used this stuff in my race car. i needed a solution, it was an oven in there, things inside the car were actually being damaged from heat, not to mention it was extremely uncomfortable. I covered my foot wells in this stuff, now the interior is slightly quieter, and the heat is almost un noticeable. This stuff is amazing. It sticks well, cuts easy, and is very easy to work with.

I used this insulation to line the doors on a crew cab truck. The reason was to reduce road noise and to add a layer of insulation to keep the Texas heat out of my black truck. So far, it did make the inside of the truck considerably quieter. Most of the road noise is inaudible, but not gone completely. It also made a difference with heat, surprisingly, as I can go inside a store mid-day and when I come back out, the interior of the truck is only warm instead of scorching hot. It was easy to cut with household scissors and the adhesive is almost annoyingly sticky as it was constantly trying to stick to every surface I accidentally touched while installing. This roll was enough to do 4 doors on a mid-size crew cab truck. NOTE: It did have the strong rubber smell for the first few days, but has gone away. Leaving the windows cracked when parked helped the truck air out.

Initially, I didn't get this for noise or sound reasons. I got this because my car would get too hot in the summer. Some days it would be so hot that i literally couldn't sit inside for 20 minutes with the A/C running. My headliner failed, so when i removed it there was no insulation up there. I looked around and this was the best value i could find. So far I'm seeing a significant difference in interior temperature when sitting in the sun. Also, there was a significant reduction in wind noise (10-15Db) inside the cabin. Sadly, I can now hear my wife's snarky comments clearly. It is a bit difficult to install large pieces alone, but with some patience and painters tape not impossible. Well worth the time and cost. Will probably buy more and line my doors eventually.

I live in S. FL. and the heat during summertime will cook food in the cab of a truck. I removed all carpeting, roof liner and seating from the cab of my truck. I installed the thermal shield in about 15 min, has excellent adhesion. I reinstalled the carpeting, seats and a cheap vinyl over the roof insulation. I turned on my truck and was instantly surprised at the minimal exterior road noise and the music acoustics were a lot better. The interior heat difference is the BEST feature. The cab of my truck would reach 124 degrees when left sitting in the sun all day and with traffic, no A/C and 5 workers the heat was unbearable. After installation of the insulation the truck does not get above 105 degrees during the day and my crew is happy. Start to finish 2 men 20 man hrs. for installation. I am going to order more to insulate the roofs and walls of my work vans. Cheap solution to a never ending problem in Florida! Good Product!

If your gonna press it with something else the adhesive will be fine I installed in on a curved clean surface and started to unstick. So if you where to lay carpet over it or a headliner or something that pushes it to the surface your sticking it on to it’ll work fine. As far as isolation I can’t speak on that it’s common sense you will get some sort of isolation but how much? Well that’s the thing. Works ok I guess feels a bit light for what I thought would be foam seems ok if your cheaping out and just want to stick and go this is it. If you’re more interested in serious reduction of heat or noise get something else you get what you pay for pretty much. I give it a 4/10 adhesive is weak and foam feels to cheap to truly isolate noise and foil seems to flimsy to repeal heat. Makes me wonder about the longevity of the product.

Utilisé pour remplacer le calfeutrage du capot moteur qui s'est fait dévorer par une fouine. Facile à poser.

So far, very impressed with the first package I bought. I bought it to put on furnace ducts in the basement. Some of them were 'drumming' while the furnace was running. Also had a few of the round 5" pipe that were buzzing. (Resonating with the furnace fan.) Cleaned surfaces as they were dusty and everything stuck well and worked perfectly. They don't have to be ultra dense. Just enough to deaden the metal so it can't resonate. Afterwards, used it on the underside of the fibreboard transmission tunnel on a classic Triumph Spitfire. No one should expect ANY of these products to fully fit deep compound curves. I cut the pieces to fit the curves and then taped up the seams with Aluminum Duct tape. Matches the surface of the patting and waterproofs all the seams nicely. Completely deadened and waterproofed this somewhat fragile item.

Weiß nicht was einige hier für Probleme hatten 🤷🏼 Habe meine Motorhaube damit neu gedämmt. Trägerpapier ließ sich ohne Probleme lösen, Zuschnitt war leicht, reichte normale Haushaltsschere und für kleinere Ecken ein Cuttermesser. Klebt bestens, natürlich sollte der Untergrund gereinigt werden. Habe Absolut nichts zu bemängeln.

Bon article utilisé sous un capot de voiture ancienne et ça tient depuis ...

Good