The Original Fix-A-Floor Loose Tile Repair Adhesive - Tile, Porcelain, Ceramic, Marble, Stone & Wood. Custom Tip for All Grout Sizes – 10.1 oz. *for Best Results Use The Proven Power of a Caulk Gun*

Works very well. Just follow the directions.

We had a bathroom remodel back in 2020. And after about 6 months, a couple of tiles started shifting and breaking out the grout. This resulted in the tile coming a bit loose. I pulled the time and replaces the mastic, reseated it, allowed to dry and then re-grouted… about 8 months later the same issue with the tile flexing and popping upstarted. I decided to try Fix a Tile instead of going through the entire process again. While the recommendation is to drill a couple pilot holes in the grout, I decided to dremel out all of the grout to ensure the best fill possibilities for the Fix a Tile. I also purchased a syringe kit for this. The description is exact. The product is the consistency of Elmer’s glue. I used the syringe to inject the product into the grout lines and it wicked under the tiles in the problem areas. I used a bout an1”x3” syringe full for the areas. I then weighted the tiles. 24 hours later the floor felt more solid than when it was installed in 2020. I re-grouted the floor and it had been wonderful ever since. I wish I would have gone with Fix a Tile the first time I repaired the floor.

I used this for 12-in ceramic tile. I only had 3 spare tiles from the tile installation, and had already used those. I noticed grout breaking up at a corner and found a total of 10 tiles, roughly in a square, that sounded hollow. I drilled one hole on each side initially. My one little tube did not do the job. It is only 10 oz. and there is significant waste with adhesive exiting the holes. I had trouble getting the product to easily flow under the tile as shown in the video. I wound up drilling more holes until I got what seemed adequate coverage underneath. After 24 hrs, about half of the tiles still had spots that sounded hollow. I drilled 32 holes total. I used a 1/4-in. masonry bit which jammed frequently when trying to drill. (The tiles are set with those little spacers which are not exactly 1/4 inch. ) A 3/16-in. bit MIGHT work better, but I did not have this size. The tiles are down much better than before. Hope they last. Expect one tube to treat 3-4 tiles. My job took 3 tubes. The adhesive seems a lot like Elmer's glue in flow characteristics and tackiness. Cutting the applicator tip is important. It needs to fit snug inside the drilled hole without bottoming out. Start with a narrow tip and shave off slices until you get it right.

I recently spent $11,000 to have a porcelain installed in my kitchen and foyer. The installers worked really hard for 4 days when the salesman labeled it a 2 day job. The installers were pressured to finish and worked 14 hrs on the last day a Sunday and had a new job Monday morning. In their haste they made a few errors. Rather than going after them, I decided I could repair the loose tiles. I found your Fix-a-Floor online and watched the brief video. I gave it a shot plus used the rest on other tiles that were loose plus installed a threshold of aluminum. The process went as easy as the video showed. The milky thin adhersive had me worried but it helped fill in all the voids under the loose tiles. I placed weighted water buckets on the ties and waited 24 hours as instructed. Cleaned the excess adhesive that excreted from under the tiles and the adhesion was amazing. 5 stars all around for Easy use, Thickness and adhesion. I will come back in a year or two if it does not hold but I feel like its rock solid. Thanks very much. excellent fix.

This stuff was amazing, saved us so much time and money. It is shockingly simple. It truly is as easy as the videos show. I read someone was not happy about how runny it is, if you put your finger over the tip as you move from hole to hole, it will eliminate any leakage from the caulk gun. We bought a house where the previous owners had installed outside court yard tiles throughout the entire house. We are using it as a rental, so decided to keep them. The grout under the kitchen section had come loose- a large area. it is now a solid floor again, no pulling up tiles. Literally the hardest part was drilling thru the grout and that wasn’t even really hard. Watching the video is essential and weighting down the area for 24 hours-patience is a virtue people.

Do not use on laminate/vinyl floor. This is my third tube of this product trying to stabilize a 2’x2’ dip in my laminate floor. The product is very runny and looks like a mix between Elmers glue and water. It “hardens” into a spongy consistency. Half the product slipped by the piston in the tube and never went into the floor even though there was no injection resistance. Same thing happened with the 2 prior tubes.

Horrible. Couldn't get glue out of container. When I squeezed the tube a little to see if the glue was hard, the bottom burst out and all the glue went on my rug. Can't tell if it works or not since I never got a chance to use it. Disappointed. Cut small tip off and even tried inserting a small nail to make sure glue could flow. No luck. Update: I contacted the company and they offered to send a replacement tube. They said to make sure you do the following before using. First you need to make sure the tube itself has been opened (unscrew tip off the tube & pierce a hole to open & screw tip back on), If too much pressure is applied when injecting the adhesive or if you are pressing the tip down onto the subfloor when filling it can blow out the back. Will update again after I try.

Very easy to use. Drill the holes in the grout as large as you can without hitting the tile edges. I drilled holes about an inch and a half apart so I could get the liquid completely under the tiles. It worked great. It has been several months and the tiles are solid. The material should be almost liquid when it comes out. It should not take a lot of force to come out of the caulking gun. After cutting the tip, remember to puncture the inner seal or you will have a mess on the back of the tube.

Hoy en día es muy difícil encontrar buenos profesionales y nos encontramos en los suelos de gres que muchas veces las baldosas no se han aplicado correctamente, y eso que hay muchos vídeos en youtube, por lo que nos podemos encontrar que a la larga las baldosas se muevan y suenen a huecas. Este ha sido mi caso, tengo varias baldosas por el piso que se mueven al pasar por encima o que suenen a huecas. Encontré este producto en Amazon y viendo las reseñas, opté por comprar dos tubos, son caros pero creo que merecen la pena. Anteriormente intenté solucionar el problema con sacar las juntas y poner una lechada más acuosa, pero el problema, a la larga, volvía a salir; por lo que opté en comprar el producto. Mis baldosas, las juntas no son simetricas por lo que no he podido seguir realmente las instrucciones del producto, es decir utilizar un taladro, por lo que he optado, como ha hecho un comprador, retirar la junta que une 4 rajolas y optar en rellenar mediante una jeringa con punta roma. Hay que tener paciencia, ya que con la jeringa se tarda más, y hay que ir limpiando constantemente para no manchar el suelo, recomiendo utilizar una bandeja de pintor, y poner el tubo en una pistola e ir rellenando la jeringa. Después de la aplicación, es importante poner un peso encima de la zona, y dejar como minimo más de 24h, ya que depende de la cantidad, todavía estará fresco, cuando el blanco se vuelve transparente ya esta seco. Puede que las baldosas suenen todavía a hueco, pero ya no se mueven. También me ha servido para fortalecer las tochanas exteriores. Creo que es un buen producto.

La scelta di questo prodotto è stata l'ultima spiaggia ma si è rivelata vincente. Per un difetto di posa un lastra del pavimento (120*60) suonava vuota sul lato della fuga e ogni volta che ci passavo sopra schioccava. La soluzione di toglierla e rimetterne un'altra era praticamente impossibile trovandosi sotto l'arco di una porta così un po' rassegnato a tenermi il problema ho iniziato a cercare in rete soluzioni alternative alla sostituzione. Mi sono imbattuto in questo prodotto e ho pensato di fare un tentativo, nella peggiore delle ipotesi non avrebbe funzionato. Una volta arrivato insieme al kit che contiene ago e punta da 2 mm ho fatto 2 fori nella fuga, ma nel mio caso ho dovuto usare una punta da 1.5 mm perché erano strette. I fori della profondità di circa 1.5 cm li ho fatti a mano perché avendo il riscaldamento radiante avevo paura che col trapano mi potesse scappare la mano e fare danni. Una volta fatto i due microfori ho montato ago e cartuccia e con la pistola ho iniziato ad iniettare gradualmente. Una volta finito ho messo sul bordo della mattonella 3 casse d'acqua e le ho lasciate lì per 24 ore. Dopo 24 ore incredibilmente la piastrella non suona più vuota e finalmente è sparito quel fastidio schiocco che mi ha tormentato per un anno. Prodotto incredibile, color bianco che una volta asciugato diventa trasparente per cui non lascia macchie che possono rovinare i pavimenti. Con questo intervento di pochi euro mi sono risparmiato un preventivo per la sostituzione della piastrella molto più salato

Colle parfaitement... Très liquide permet de s'infiltrer partout sous le dallage, l'utilisation d'une seringue facilite l'application. Se nettoie facilement avec une éponge humide pour les coulures ou débordement sur le carrelage. Ne pas hésiter a repercer et a réappliquer là où ça sonne creux.

En toute sincérité je vous recommande ce produit

Onze vloertegels (60x60) in de badkamer waren losgekomen en voegen waren ook beschadigd. 3 tubes waren voor mij genoeg om een oppervlakte van 5 m2 te behandelen. De tegels zitten nu goed vast.