KeylessOption Keyless Entry Remote Car Key Fob Transmitter for Mazda 3 2007-2011 KPU41777

The provided website didn’t load but I followed the steps provided by another Amazon reviewer (Nocturnal) and it works as intended (2009 Mazda 3). Saved me $150 compared to my local remote guy!

I recently purchased a used 2009 Mazda 3 for my daughter and it only came with one key fob. I checked with the dealer and even the guy at the dealer told me it would be much cheaper to get one off of Amazon than order one through him.I saw this 2 pack of these and they had great reviews, so I decided to order them and see if it worked. The fobs came with a small paper directing me to a website for programming instructions. Those instructions weren't very clear so I decided to follow what I have seen on reviews here and on YouTube.I did as follows:1. Get in the car.2. Close all doors.3. Put key in the ignition.4. Open driver’s door.Carry out the following procedure within 24 seconds:5. Turn ignition switch ON and back to LOCK position 3 times. DO NOT TURN TO START AND START VEHICLE.6. Close and then open the door 3 times (ending with door open).7. The doors will lock and unlock. -If not, wait 40 seconds and repeat procedure starting with driver’s door already open.8. Press UNLOCK button of key fob transmitter twice.9. Ensure doors lock and unlock after each operation.10. Repeat steps 8 & 9 for each key fob up to a max of 3key fobs per vehicle.11. When done with all remotes, remove key from ignition. Doors will lock and unlock.12. Done.If not, proceed as follows:Open and close driver’s door once.Ensure doors lock and unlock twice.Repeat procedure starting with driver’s door already open.Keep in mind, that you must program any key fob you already have at the same time. It rewrites the programming code so your old fob will not work unless programmed at the same time you do the new one (ones).Hope this is helpful.

I have purchased two 'Keyless Entry Remote Control Car Key Fob Clicker Transmitters' from 'KeylessOption' for my 2009 Mazda Mazda3. The fob remotes worked great and I felt it was an appropriate price at only thirty dollars. I am very pleased. The only minor negative (and this is an incredibly small negative as the product still got an outstanding 5 star review from me) is after about two months of daily use the white paint on the rubber buttons started to partially rub off (i.e. the “LOCK” and “UNLOCK” buttons). This issue happens with all fob remotes but it seems to begin much sooner on this one. Again, this is a non-issue for me but I figured I would mention it. I have ordered two fobs and both were identical to the originals with one exception. These fob remotes come with a 3 volt CR2032 battery installed whereas the original fob remotes use a 3 volt CR2025 battery. CR2032 batteries can be purchased anywhere so this is another non-issue but I wanted to be informative. One reviewer advised it did not open his trunk but it opens my car’s trunk.I have a 2009 Mazda Mazda3 and these are the instructions I used for programming my new fob remotes:1. Sit in the driver’s seat with all doors unlocked and closed and ensure the trunk is closed as well.2. Open the driver’s door.3. Put the key in the ignition and cycle the ignition from ‘Off’ to ‘On’ three times (do not start the vehicle, just put it in the ‘On’ position). It should go: on, off, on, off, on, off.4. Close and open the driver’s door three times (immediately after you do this, this will make the doors lock and unlock automatically which signifies the car is in programming mode). It should go: close, open, close, open, close, open.5. Immediately press the unlock button twice on the fob remote you want to program (immediately after you do this, the doors will automatically lock and unlock which registers the ID in the fob remote to the vehicle). a. If you have another fob remote to program, immediately press the unlock button twice on the next fob remote you want to program (this will make the doors lock and unlock again). Repeat this step for as many fob remotes as you want to program. If you do not have another fob remote to program, just skip to the next step.6. Take the ignition key out of the ignition (the doors will automatically lock and unlock two times signifying the car is out of programming mode).7. Test all fob remotes to ensure programming was successful. Note that you only have about 24 seconds to get the car into programming mode or you will have to start over.Click 'Yes' below if this review helpful to you. It makes me feel me spending thirty minutes on this review was worth it :)

Didnt get programming instruction with the remotes. Went onto their website and they have nothing. Went to utube and all the programming videos say the same but didnt work with these remotes. Bummed...They were easy to order, did get here on time and looked good. Only reason for 2 stars.

I have to say, I bought this thinking there would be a 50-50 chance of it working. Well, I am happy to say that it works perfectly! I have a 2009 Mazda3, and no issues at all. I did have to take a couple of tries with the programming, but after reading some of the other reviews, I got it to work. Now I can't quite remember which set of instructions I followed to get it to work, but it was either the ones that came with the remote, or one of the most recent reviews. I know that's probably not super helpful, but I do know that the first time I tried the instructions that came with the remote, it didn't work. I think it was because I had the key in the ignition from the start, but like one of the other reviewers noted, you should really put the key in once the driver side door is already open. So, just check out some of the recent reviews for alternative methods in case the instructions don't work for you the first time. But, like I said... There were just a few minor tweaks and I couldn't believe that I finally will be able to lock and unlock my doors remotely! The remote has a nice quality feel to it as well. And bonus that it comes with a battery!

Lo programe en 15 segundos literal. Funcionó a la primera y por el precio está súper bien. Super recomendado. Pediré otro.

Me gustó mucho pues mi control ya no servía el chip y compré este modelo que era el mismo y me funcionó a la perfección

Producto de buena calidadMuy facil de programar, recomendado...