Solder Sucker Tool No Clog Silicone-Tip Manual Desoldering Pump Soldering Accessories for Solder Remover – Unrivaled Suction • No Power Needed • Ultra Low-Maintenance • Best-in-Class Desoldering Gun

I've been soldering my whole life, and I've sucked some solder in my day, but this is the best solder sucker I've ever used. It's a better built device than any I've had before, with a smooth action, a virtually silent operation, and it just works beautifully. A second press after the completion of the suction expels the waste solder from the gun. The silicone tip won't get stuck by the solder due to the silicone tip. It works smoothly, perfectly and silently each time I press the button to enter stealth mode, and I'll never again buy a cheap solder sucker! I've spent my life buying sucking devices that work, but aren't pleasing to operate. Remember those little Yugo cars? I've been apparently operating Yugo solder suckers my whole life, but now I've purchased the Bentley of solder suckers and it's a life-changing experience! I'm spoiled and will never go back. This has an elegant and solid feel, Sure, it's a bit more expensive, but not that much more! After trying this out, I fully expect it will operate much, much longer than the cheap ones, thereby earning it's price!

I used to do a lot of soldering/de-soldering back when I was employed in electronics, hence I miss the fancy de-soldering equipment that's out there today. But since I don't have a place for all this equipment, this solder sucker tool is a good tool for occasional de-soldering, and it's cheaper and smaller than the large de-soldering units I used to use.

Amazing tool once you have the hang of it. Use this to assist in doing stick swaps on controllers to remove solder. It along with the de uni A heating pad has made the process pretty streamlined and easy for me. I have had no issues with this sucker it works very well for the job I've been using it for and it cost a fraction of the price of the well known name brand one.

1. don’t disassemble the rear side of it, you could lose suction permanently 2. if the button feels too hard to push, add some lubricant to the metal cylinder where the latch catches. Mine was so bad I’d shake the whole thing trying to push the button and miss the solder. I kind of wish I had just spent the extra $10 to get the japanese one instead of this knockoff, but I don’t solder often so I still expect this to last a while. It does work pretty good, it just seems like a slightly flawed imitation to me. Also some of the pre cut spare silicone nozzles are too short to use, wish they just included uncut silicone tubing.

best solder sucker I've ever used

Works great, very strong suction just make sure you have it completely covering the melted solder for maximum suckage!

This product works extremely well initially, though ive found that over time the no clog claim is false. Over time ive found that it is necessary to clean all the way back to the gasket, though I wish I knew what kind of lubricant is inside it so I could replenish it properly. You'll notice the clog once the needle requires quite a bit of force to push through with the plunger. I used this on a single PCB with a few hundred through holes to clean out, so its definitely getting worked thoroughly.

Yeah this is just better than those other ptfe ones. I'd get one of these and not look back. Dont bother with the possibility of ptfe fumes if you hold to long. I feel like this needs less unclogging too. The one MAJOR drawback is that the silicon tips you get will break and i recon they should give you more than what you get. The reason I am not taking a star off for this is because ive actually had the build in PTFE tips break too while trying to clean them. You can possibly mitigate damage to these silicon tips if you just pay attention to where your solder is getting stuck after use. Anyway this is about as good as you're gonna get without an automatic one and arguably nicer to use than at least the bare minimum one-handed powered plungers with the basic metal tips. Haven't used the fancier ones.

El cuerpo es de aluminio, el piston y resorte se pueden limpiar accediendo tan facil como desenroscar. La succión es muy buena, solo tengo que dar una o dos veces para retirar soldadura y trae varias boquillas que son flexibles y ayudan bastante.

基板修理やパーツ交換のために購入しました。 期待通り吸い込みが非常に強力で、スルーホールのハンダもしっかりと吸い取ってくれます。バネの反発もちょうどよく、連続して作業していても疲れにくいのが良いですね。 この価格でこの吸い取り能力なら十分満足です。これまで使っていた安価な吸錫器とは比べ物にならないほど快適に作業できています。DIYでハンダ付け作業をされる方には、持っておいて損はないツールだと思います。

Works really well. And some extra silicone tips. Works very well.

Its a must! Very easy to take off the old solder by this. I do it for the fist time and I don’t have any hard time at all

Really solid build. Great buy even if you just use it occasionally. You won’t regret it if you are using the cheap, plastic ones.