Front Lip ,HengJia Auto Parts 2.5m/8.2ft Car carbon fiber front lip,Front Bumper Lip ,Carbon Lip ,Side Skirt, front lip spoiler 100% waterproof protection(Carbon black)

Installed on a Subaru Crosstrek. Be advised that it has an obnoxious chemical smell upon opening. Just lay it flat in an unoccupied room for a few days. The smell mostly goes away. The installation instructions were in Thai. Lol But there are pictures tho. Had to clean the underside well with wipes/soap/water/alcohol. The cleaning may take a few rounds, but very important. It won’t stick to a dirty surface so don’t get mad if it falls off later on bc you’re too lazy to spend the extra 5-10 minutes to really clean the underside. (Just saying.) It comes with two adhesive promoters but it should have come with 3. They dry out pretty quick, but are essential for the adhesion process. It does take some time to measure and cut out the “triangles” for the bends. I just used a pen to mark on the red tape to guesstimate where the bends are and marked the triangles from there. Also, you’ll have to force the lip to bend. The lip is rubber, it’s not all that elastic. Would also recommend utility scissors to cut the triangles too. The rubber is thick enough that I’m not sure normal scissors will get the job done. I had to use two hands to clomp down on the scissor handles. It’s been 3 days since the lip application. Hasn’t fallen off so that’s good. Also haven’t used the screws yet but will probably put them on. Haven’t braved sending it thru a car wash just yet so may have to send an update for that later on. All in all I like it so far. Considering buying two more for the side skirts IF the front lip lasts thru a car wash. Lol I do like that it’s rubber bc cracking a real lip kit would make me cry. *Update (4/3/18): Front lip still on after 4 automatic car washes and a couple of thunderstorms later. Still haven’t gotten around to putting the screws on either. 👍 **Update (2/4/19): Front lip still on. Eventually had to add 2 screws to one of the bends bc it was starting to fall off at the ‘corner.’ (This was the same place I had to cut “triangles” to make it bend.) The screws were recently installed in Jan. 2019 so the lip held up well with all things considered. Sadly the front lip had an unfortunate run in today with old debris from a blown tire. The car in front of me kicked it up so fast that I didn’t have time to swerve or brake safely at highway speeds. Poor car took it like a champ. =/ Oddly enough, the lip is still on. However, the center portion of the lip split horizontally right where the lip and adhesive part meets in the middle. Will probably have to replace it eventually as rubber will degrade making the gap even longer. However, I will be purchasing another three once it’s time. I’ll redo the front lip but also add side skirts. ***Update (03/05/20): The original lip is still on! The adhesive is wearing off on one end near the wheel well, but not bad for 2 year application. Got lazy and used Velcro to keep it on for now. The split in the middle has widened, but still safe to drive with. Ran this thru the car wash well over 30+ times. Some of the carbon fiber graphics has worn/scratched off, but still decent shape with all things considered.

OK 1st off the problem with this thing is that I really genuinely wanted to love it one it does not say samurai on it it's just carbon fiber color. To the eat it provides for screws to attach it. The problem with that is that there is adhesive also but it only lasts for about 5 days. So the moment you put it on it will look great but within a week it will be sagging down everywhere. I added about 10 more screws and it still sag in between each screw. I put it on a Porsche Panamera and and looked cool at 1st but I had to rip it off within 2 weeks next time I will buy something that is made out of hard material double not sag due to basic I. Understand that it is summer time but this is a very temporary purchase and should only be used if you expect it to look good for a couple of days. Don't waste your money find something that is made of hard plastic not rubber that has poor adhesive

The product itself is not a cheap product it’s about an inch thick of rubber on the other hand tho the adhesive that comes on the product to stick to the car is not good YOU WILL NEED (3M ADHESIVE TAPE) you can go to any oreileys autozone Walmart or any car store and find it I put a picture up of what it looks like I’ve had the product over a month and a half and had no problems with it once I put the 3m tape on it I’ve washed it multiple times as well as I Have a high powered pressure washer I use and it still holds...on the tape itself is like 3$ YOU WILL NEED 2 ROLLS don’t hold back on the product it’s good and will get you compliments just needs a little more stick nothing serious

Took a chance on this cheap lip. Yes im aware it needs to be screwed in but I didnt want to and if it fell off cause of that so be it. Ignored bad reviews. Was fairly easy and straight forward to put on. Was great for the first month. Highway use and everything was cool, yes with no screws. Month #2: I notice the red trim color faded to pink. I guess the sun is brutal down here in Georgia. Colored over it with a red paint pen but that too faded LOL oh well. Maybe a vinyl trim would work better... Later in the month the 3m weakened in one spot, I was prepared for this and reinforced it with more 3m tape, all was well for a couple more weeks. Month #3: Hit a bad patch of road. My front bumper was protected but lip got ripped. Managed to salvage it with more 3m tape and buy myself a few more weeks of use but by this point the writing was on the wall. Today was the last gasp as most of the lip ripped off the car when I backed into the driveway. I had a replacement EZlip liner waiting for this day. Will be putting that on now. Elapse 1 Year: EZlip stayed on but didnt stay looking pretty. It was longer and more prone to getting scraped along the ground. Didnt protect my front lip as well either, ironically... I'll admit it, I miss the cleaner look of the cheap Samurai lip. Today my oil change place did me in and hit my front lip against a parking curb so the EZ lip has to be removed and front lip repaired and repainted. At the end of the day, its not fair to fully judge this lip without screws. I am now in the process of either deciding on slapping an STI lip underneath my other lip as a skid plate or giving this liner another go, this time WITH screws. Either way, for the money, this aint bad. Without screws, it'll only take 1 bad hit but at least it will protect your stuff. With screws may fair even better! Perhaps it depends on the car and how low you are.

You get what you pay for. Once I bought it I was nervous about the angles my bumper has, stupid things like do I make straight cuts, angles, straight once I get to the end point.... HERES THE EASY WAY. Get some rubbing alcohol, dont douse your car but a quick wipe of thick debris with a cloth and quick wipe of alcohol and you'll have a surface ready to stick. These guys use real 3m adhesive. It wont hold on it's own. But start at an end point. Right or left doesnt matter. Dont overthink it. Start going along getting it to stick by pressing hard for a few seconds every 5 or 6 inches as you go along. When you get to crazy angles you gotta take a pair of scissors or razor blade to make a v or angle cut that can overlap. Hold those angles for a few seconds longer to get it to stick as you work across the bumper. When you reach the next side, or the end, make a cut. I matched each end with a 60ish degree angle back to my cars fender at the bottom. Again, dont overthink it. Go back along and really press hard on the strip, especially those angles. Then the MOST important part. The self tapping screws. Its under your bumper. You'll never see them or the holes if you take it off but you chose a 32 dollar roll on bumper. When you go to put them on remember you're under your bumper and a drill may not fit. I only used a small stubby Philips head screwdriver. Press hard at first and the point on the screws will place themself a bit. Press hard towards the bumper and then screw until its pretty snug without snapping the plastic on your bumper. Do the ends. Do the middle. Screw into the angles and even grab 2 or 3 extra to do the same thing and this will not fall off. I recomend unrolling it for a night or half a day maybe inside in a warm house. My only gripe is the straightest part of my bumper is a but curvy because the temp outside I am installing in, the fact it's still new and it's just a rubber strip. I have a 2x4 placed lightly on it to straighten it out until I give it a try driving. I cant imagine it coming off as the screws are more than sufficient and the adhesive seems legit. I would still only use with the screws and they should give you 2 or 4 more in the package. For what this is, it turnt out great. Will post a pic soon and update after driving a bit.

The product itself looks great and the lip itself appears to be great quality but all that is ruined by a terrible low quality adhesive that doesn't stick. Mine lost all adhesive in less than 24 hours after installation. I'm glad that I screwed the thing to the car because I would have lost it by now on the highway. Very dissapointed with the product because of that issue. I shame because it looks nice.

So look in the pics and see that this is the correct way of installing this. First off I cut relief spaces around 4 inches apart. I used like 50+ nuts and bolts w/ red loctite. Once lined up (pretty much just eye balled it) on the bumper drilled one hole at a time and dropped a screw in without a nut. Once I made it all the way around i pulled off the rubber and made sure everything was clean and smooth. Once cleaned all was left was to pull the backing off the tape and put on the bumper making sure the bolts lined up with the holes going 3 sections at a time. Then this is the most rewarding part....Must have a heat gun ! Break out the ol heat gun and start warming up the rubber making sure ya don't cook it. Just get it to where you see it start to move a lil with the heat on it swiping back and forth in foot sections. All those imperfections are now gone (wavy notes on the rubber due to curves and what not). When the rubber cools down it will get more stiffer again so don't worry if it feels soft. All your looking for is crisp even lines. You'll understand when you get it out the box and pieces look like " how the hell is that gonna even out". The 3m tape pretty much is garbage and I knew that from jump street so I could have gone with rivets or bolts. I went with the latter just in case i need to replace it one day. Looks at the pics I have a 2014 Hyundai Sonata and it pops now with this on there !!!

I live in Ohio. I read the guys review from Ohio saying how well it stuck without the screws and he had no issues. Sold! Well lol, he is either the dude who sells this or is a paid spokesman. Mine stayed on for 3 days. That's it. And I even used the included screws for reassurance and good thing or it would have been off and on the road by now. PS, 4 screws is not going to cut it if it don't stick. 8 maybe but not 4. And most people don't have self tapping small screws just lying around. It stayed on the straight front parts but failed on both corners. I feel like I should have gotten paid for how crappy my car looked on the ride home when this happened btw. Stuff just hanging off the bumper....so I learned that yeah it looked good when attached correctly and that one great OHIO review should not sell you when there are 50 other bad reviews saying it does not stick and that there are not enough screws. They are correct. Man though, that guy had me pumped with the updates and everything. Like if it made it here it can make it anywhere aditude. And I'm from OH too so everyone else just don't know how to properly install. That's what the issue is! Lol nope no it isn't. And if that guy isn't payed you should btw. He is the reason your selling any at this point.

سيء جدا جدا جدا

سرعة الشحن

色が白っぽくカーボン調と言うより2Dの安いプリント模様。折り畳まれた状態でくるので、外で日光に当てて伸ばしたが、軽く波打っている状態。ヒートガンで加熱をしたが最後まで真っ直ぐにならなかった。3Mと表示されている両面テープが貼られているが、こんなに粘着力の無い3Mテープは無い。剥がして本物の3Mテープを使用しました。カーブのところで三角形をいくつも作り曲げていきますが、材質の硬さのせいか曲げた後が突っ張って浮いてしまう。養生テープでガッチリ固定し対応。 出来上がりは、カーボン調にも程遠い。艶も無くいかにもプリントしたシルバーぽいものがバンパー下に付いた感じ。パッと見ても安っぽさがすぐわかる。何のために付けたか聞かれたら、リップスポイラーのプロテクター。と、言って自分を納得させるしかない。金銭的にも負担になったが時間と手間を費やした事に頭にくる。 購入を考えてある方、クオリティが低いのでやめた方が良いです。

It was easy to install but the adhesive is not the greatest thing so it is good that they gave you screws to use

هو ليس كما في الصوره ..