Sovol3D 2 Pack Stick On Gasket, Screen Protector for 5.5" & 6.1" 3D Resin Printers, Universal Protection from Resin Spill, Fits for Mars Series ANYCUBIC Photon QIDI Tech 5.5s - Resin Resistant

I bought this to replace the adhesive tape that comes stock on my printer because the tape had been damaged from a leak in my fep sheet that I hadn't noticed. After another failed print there was built up cured resin on the screen itself but thanks to the film that covers the screen itself on this product all I had to do was replace it and not have to worry about a screen replacement.Tldr: works great as advertised and as a screen protector from leaking resin and scratches.

I've had a heck of a time trying to use film covers like these but these were actually easier to apply than others and has been holding up just fine

This product looked just like a big name screen protector, but obviously I got what I paid for. The adhesive is very strong- so much so, that it will peel off the lcd screen tape, if not careful. But, this prevents the bubbles from being removed, so matter how delicately I tried. After 40 minutes of trying every technique I know, I realized that the film was becoming warped in the areas that I had been able to coax the bubbles out of, making it useless for resin printing. The instructions are lackluster, and I would not recommend these protectors for this particular use.

I got this for my Elegoo Mars 2. The fit isn't quite exact - it's just a little larger than the recessed area, so I was a little worried it might mess with the prints and made sure to realign the printer. It works well, but resin sticks to it like crazy and I can't get it off. I was only able to use the first one for a couple prints. The second one is doing better, but I have to be extra careful. They also leave a lot of residue when you pull them off. For now, this does the job and is an acceptable replacement.

They worked on the printer.

It usually works fine but recently I got one where the inner adhesive wouldn't come off.

Works perfect for my elegoo mars 2.0 pro

To be blunt, it works to a point.Pros: •it is a clear non adhesion clear center screen protector with a strong adhesive outer black gasket.•it comes with a clear protective film that you remove after install•the outer gasket is stout, so no chance of it curling like a sticker; ever.Cons: •way too many to list. But I will list a few•the clear film that you remove after install is not so clear. It isn’t clear enough to see through it to line up the protector correctly, so you have to shine light through it or peek off one side to line it up perfectly.•the stout black gasket is too stout. If your printer like mine has a lip from the screen to the base of the printer; the gasket doesn’t bend and fold down the lip. It just angles itself and causes all the edges to lift off the screen. So the very center is only flush. This causes air bubbles that, no matter what you do, won’t come out.•after my install, with tons of bubbles, my prints have been coming out with bulging layers. I assumed it was just bound to happen over time, so I did basic z axis maintenance on my printer. Nothing changed. Will be removing it tonight.•the strong adhesive used on the gasket comes off when you remove the screen protector. So you then have to spend several minutes scrubbing it off. It’s not so easy.•the package comes with two. I’ve purchased 2 sets so far. Im on my 3rd because if one tiny little drop of resin leaks down the vat. It Will carry into the corner, don’t know how. This was never an issue without the screen protector. It then ruins the screen protector. Unlike your screen, you can’t get the resin off. It ruins it right off the bat. So Ive gotten 5 prints out of 3 screens. I’m very careful not to spill or drop any resin. However, when the print finishes, and it sits waiting. It does splash as it drops. This causes very small droplets to either fall on the vat or on the plastic dome. The droplets on the vat may fall back into the vat or they may fall out of the vat. Originally I could just wipe the bottom edge of the vat and it wicked up the resin. With this screen protector, it rides up the edge and gets to the screen and ruins the screen protector.Verdict: find something else. Something better. Mainly if you have a screen that is slightly lifted. As in, has a lip. If you don’t want the hassle of paying 10$ for 2 and replacing them twice a weak from a micro drop of resin getting on the screen; then find something better. I have went through 3 so far. I have 1 left. The 3rd is being removed tonight to attempt to see if it’s the cause of the bulging layer lines. I’m assuming it’s because the screen protector doesn’t sit flush around the edge and causing it to lift on the edges. So I’m going to remove it and risk ruining my screen; that’s just how bad this one is.

Bonne qualité pour le prix je vais en acheter d'autres

La pantalla es muy opaca, nubla demasiado la luz de la impresión resultando en completas fallas en todos los intentos, incluso cuando aumenté el tiempo de exposición en la impresora, la recomendación en las instrucciones de aumentar la exposición por cada 10 segundos es una locura, no solamente hará que tus impresiones tarden exponencialmente más, sino que te obligará a reemplazar mucho más frecuentemente la pantalla que intentas proteger.

La protección es ideal para la Photon Mono de Anycubic. Eso sí, su instalación no está del todo bien explicada: se ha de quitar el adhesivo trasero además de la lámina de papel que iría sobre la pantalla LCD (es un proceso pegajoso pero no dificil, también evitar tocar con los dedos la zona transparente). Luego con cuidado se aplica sobre la impresora habiendo limpiado bien los restos del anterior pegamento y el polvo de la pantalla. Finalmente, asegurando que no hay burbujas, se quita la protección exterior. A tener en cuenta que hay que aumentar 10 segundos el tiempo de exposición de las CAPAS INICIALES, no de cada una porque sería un infierno. La he probado estos días y ha ido perfectamente y sin miedo a los derrames.

Discription is a little confusing when it says and shows 2 on the advert. When actually it's 2 into 1. You have to be very precise fitting the first peel off over the glass, as I discovered when doing a light test I had a slim gap one end and had to use black tape, But pleased with it over all.

Ottimo acquisto per la protezione dello schermo lcd