Winegard DS2000A Universal 22-inch Mount for Off-Air TV Antennas,Grey

I used this to mount my starlink version 2 dish off the side of my house and it worked pretty well. It's almost perfect. The original dish mount has a key in the bore that registers on the bottom of the cable connector. It makes the cable almost impossible to become disconnected once the dish is mounted. The Winegard doesn't have this provision and I missed it when I was checking the fit. It would have been fairly easy to mount a tab in the bore of the Winegard mount but I just didn't see it. Consequently I had to remove the dish several times and re-seat the connector as it kept falling out. The last time I wrapped the connector and the cable with electrical tape and it is holding fine for now. If I have to revisit the mount I will add a more permanent solution. No fault of Winegards. The mount is well made and is still a great way to mount the dish.

Bought this to mount my over the air antenna. Right away i could tell this mount was made with good materials and had a nice hefty weight and feel to it was very pleased. Assembly was pretty straight forward and mounting it too. Had out side for a while and its doing its job can't complain a good buy.

With the plastic adaptor I also bought on Amazon my rectangular Starlink antenna snapped right in and had plenty of clearance to auto-find the best satellite to connect to. I had already verified where the antenna was going to auto-position itself, so I didn't need a 100% clear view of the sky. I opted for a strong mounting point (we often have really high winds here) over a weaker mount point that had a full view of the sky. Whether you buy the plastic insert or not, you'll have to secure the antenna from spinning in the antenna mount tube. 2 or 3 self tapping sheet metal screws should easily do that job for you.

Worked well. Had to shorten mine a bit, but it worked well for my 2nd gen starlink dish. Added a few extra self tapping screws to stiffen it all up.

Starlink is my ISP and instead of using their supplied ground base or purchasing one of their mounts, I used this to mount my antenna to an eave on my house where it has an unobstructed view of the sky. The antenna dropped right into the end of the tube without any issues and it stays put. The mount is sturdy and has enough adjustment to get the antenna away from the roof line to allow it to adjust for the best signal.

Finally had Starlink internet in my area after 7 years of dreadful Hughesnet internet. Our area is monopilized by ulitlity companies that left us with no choice but we enjoy our land away from the city. This mounting bracket is solid and does its job. Had to use a 1 1/4" to 1 1/2" coupler to connect the Starlink's receiver. It's been holding up for almost a month now and we are really happy that this product exist. Now we have a smarthouse because it was a dumbhouse for 6 years of having slow unreliable internet.

Good product.

The height of the mounting area is quite long and wouldn't quite fit on our rood soffit board but two big lag bolts was plenty to hold it securely. Starlink slides into it easily with minor modifications using duct tape to widen fatten up the tube. Then I used a few wraps of electrical tape to hold it from sliding down further since the Starlink wire will get pushed if you don't keep it secure fastened to the mount. This worked fine.

This is the perfect fit for my starlink dish and it does its job very well, especially with the attachment and handles all the weather conditions on a flat top roof, especially wind.

Some have claimed that this mount does not provide a tight fit for a rectangular starlink unit. That is true if what one expects is that the mount provides the same insertion fit and 'button' locking you get from a standard starlink mount. It does not do that. But the internal diameter of the mount is 1.52" and the starlink's shaft's largest diameter (beyond the reduced-diameter starlink-specific mount area) is 1.5". Wrapping some electrician's tape around the 1.5"" diameter area of the starlink unit might be enough to get a tight fit. But better, I think, is using a 1.25" flexible pipe connector (1.25", not 1.5", because the outside diameter of 1.25" internal diameter pipe (metal, ABS, etc.) is approximately 1.5") provides a waterproof and more stable solution. Put the pipe connector on the mount shaft, leaving about an inch of rubber (actually black flexible PVC) for the starlink shaft and push the shaft into the mount about 2", thereby placing about an inch of the 1.5" shaft in the mount. You could even wrap tape around the shaft too. Tighten both clamps. Be sure, of course, to put the starlink cable through the bottom of the mount and insert it in the starlink unit before inserting the unit into the connector that is placed on the mount. I can't guarantee that this solution provides as much stability as a starlink mount; among other things, placing the starlink unit on a 22" shaft rather than locking it into a starlink mount that does not add length to the shaft of the unit unavoidably allows more movement. But of course, adding more height to the starlink unit can be advantageous too.

Easy to use with Starlink receiver. Very good fit. Well made

what I like about this arm is the greater reach the longer arm provides. easy to install. what I do not like is that it does not provide enough room to run the cable at the base, (I have It Mounted on my sloped Roof). I had to grind a half moon at the bottom of the tube. Also, the inside diameter was a bit too big for StarLinks Dishy McDish...so I used my McGyver Skills and made it work.

Very happy with my purchase. All good no issues.