QWORK® Battery Capacity Tester, Battery Monitor, Voltage Range 8V-80V and 0-100A Sampler base, with 6.5ft / 2m Custom Cable, for Auto Car Motor Boat Caravan RV

This is working fine on my 24v lithium system. I am using it to monitor two 12v 110 amp lithium batteries in series (24v)i have been using it tor a few months now with no problems

Great 4m cable !!! The 350A model is taller than the 100A model Be careful not to bend it! *My tips* (Not expert) Mainly for motorhomes: Note. To set backlight always off: Hold down both arrow buttons together for 3 or 4 seconds. To later temporarily illuminate, press the “A” button, briefly. To set backlight always on: as above. (It will flash on and off during charging.) but when the resultant current (explained later) flow is below 100mA, the backlight always automatically turns itself off. Note: The level of current shown on the “A” screen depends on two factors: 1. The current now going into the battery which perhaps depends on the solar charger and the Sun and the 240 V charger. 2. The current flowing out to devices which opposes 1. to give the resultant current. (The meter will detect tiny currents drawn by such things as the standby current for the solar controller and Bluetooth devices.) Note: The Current Screen has two displays: “A” and “Ah”. Pressing the A button swaps between them as shown on the screen. “A” shows the current now flowing. Note: Perhaps you can use the following method to set up the meter without discharging your battery to zero Volts. * Set the meter to remember your battery's claimed capacity (Ah)* 1. Wake the backlight if needed by pressing the A button. 2. Show the “A” screen on the meter if needed (Current Mode) by pressing the A button again. 3. Show the.”Ah” screen on the meter by pressing the A button again. (Setting Mode) This shows what the meter thinks your batteries claimed capacity is. 4. Correct this figure if needed by holding down the A button for 3 seconds to enter the blinking setting mode then pressing the arrow buttons to match the “Ah” written on the battery. 5. Press the A button again to save and exit back to the “A” screen. *Set the meter to show when your battery is full (100% capacity)* 1. Charge the battery to full. 2. Wake the backlight if needed by pressing the A button. 3. Press the % button to show the present presumed capacity. 4. Hold down the % button for 3 seconds to correct to “100%”. Done!

The monitor works OK when combined with a shunt. My only gripe is with the instructions which are difficult to read as the font is TINY! Also the symbols both on the monitor switches and in the instructions are almost too small to decipher.

Great battery monitor, installed to visually monitor my vehicle battery, especially in winter months, no big screen, fits neatly here I can easily monitor performance and potential degradation.

Found this gauge and shunt quite easy to install . Not sure if any reason not to do it the way I have . I found the bolt on the shunt was the same thread as my renogy 24v 100ah battery . I just removed the bolt in the battery and took the nut off the shunt and bolted the negative side directly to the battery as picture . One thing to note is you need a thin piece of red wire not supplied to go to the positive of the battery . The gauges tell you battery percentage , amp hours remaining, voltage, the amps going in or out of the battery. Would have liked to see wattage but for the price it's ok

Very pleased with my purchase. Was simple to install and use and seems to give clear accurate reading of the battery state.

It works. It doesn't work

No idea if it works or not yet because I'm still making a bracket for mounting it into the van. If I'd known earlier, I'd have sent it back for a refund. It's become a hassle and I expected a device like this to come with a mounting bracket.

No issues, installed it in my boat, looks really sharp and has been very functional.

C'est exactement un testeur de batterie que je recherchais. Pas trop d’options inutiles et pour un prix très compétitif. Comme l'appareil fonctionne avec un très bon shunt, il surveille à la fois la charge et la consommation de courant, vous donnant ainsi un aperçu précis de la capacité disponible de votre batterie. La tension actuelle (V), le courant (A) et la capacité disponible (Ah & %) peuvent être lus.

Seems to work well. Easy to read. Pleased with purchase.

Leuk dingetje, doet zn werk. Maar de leesbaarheid en duidelijkheid van de handleiding laat te wensen over. Met name de symbolen en de vertaling in het engels zijn niet goed.

Arrivato con una giornata di anticipo e subito installato sul camper. Che dire, vedi in tempo reale il voltaggio, ma soprattutto gli ampere che realmente consumano le utenze.