RealTruckBAK Revolver X4s Hard Rolling Truck Bed Tonneau Cover | 80329 | Fits 2015-2020 Ford F-150 5' 7" Bed (67.1")

Easy installation! Looks fantastic. A bit pricey but well worth the price. I would buy it again. Love the way it looks and fits on my truck. Great product and again very easy to install, love it!!

Amazing cover, easy installation.

I put this on my F-150. it took me just a couple of hours to do it by myself and now that I know some easy tricks I could do it much quicker next time. I like the flush fit, the ability to flip sections up and lock them open for going down the road with cargo. The only downside is it's not completely water proof there is a little water that gets in but it's minimal and easily channels into the grooves in the plastic liner in my F-150 so my cargo doesn't get wet.

**FINAL UPDATE**After my last update i did receive the replacement roll top and this thing has been flawless for a couple years (yea, totally forgot about updating my review). It has held up really well with Houston weather, operation is simple and keeps everything secure with minimal or no water leakage into the bed. Also i do not have any rattling or flexing while driving (generally 80+ mph down the interstate, gotta keep up with that Texas fast lane). Updating from 1 star to 4 stars, would be 5 if i didnt have all the initial issues.**UPDATE**Received a reply within 2 days of my original review, took me a few days to send the information they were requesting because I was busy with other things. They requested, Serial Number (located on a sticker on the underside of the cover, close to the bulkhead), Shipping Address, Proof of Purchase, and pictures of the issue (Please note: I don't know if theyre flexible with this but if you encounter issues, TAKE PICTURES!). I received a reply within 2 days of sending them the proof they requested and they stated a new cover will be sent to me and had additional instructions on what to do with the old cover, they did not request I send it back. They also stated that theyre sending the cover ONLY, all hardware and rail from the original purchase will be used again. Will update once I receive the replacement. Unfortunately because of demand, theyre estimating another 2 - 3 weeks before the new cover gets shipped. Keeping my 1 Star review until I have a working product.**ORIGINAL REVIEW STARTS HERE**Decided to pull the trigger on this $1K+ cover for my truck. A lot of reviews were read and watched, and seemed to really fit what I needed. A low profile hard cover that didn't take up any bed space and easy to operate. Well after waiting a little over a week I finally got the cover in and started my install. Install went well enough, nothing too difficult, but once I put the cover on to roll out and get positioned I noticed the first issue. The plastic guard piece closest to the tailgate that is supposed to help prevent peeling of the seal and guard you from sharp edges of the aluminum was broken off. Not a deal breaker, I've actually seen several reviews that said this has happened and BAK Industries has simply sent a replacement piece to clip on. Continued my install and noticed a bulge at the top of the cover towards the bulkhead, I immediately knew it was not supposed to look like that. So i went to investigate and to my surprise, one of the links to the cover was actually broken. This completely breaks the covers operation. The full siderail locking isnt able to engage, causes issues with closing, opening and the end of the cover itself (at the tailgate) ends up bowing causing a huge gap center of the tailgate and the side rails flex upward, also causing issues with contact with the cover and seals on the very corners of the tailgate.I have emailed BAK Industries and will hopefully get a reply soon with some sort of solution, if I don't I will be forced to deal with returning this thing. If they do respond and offer a solution I will update my review with information on that.

About as good as it gets in tonneau covers- durable, attractive, nearly watertight, and easy to install. Working solo and very carefully it took me under 40 minutes to install the Bakflip F1 on a 2015 F-150 with 5.5ft short box.Helpful hint: most installations route the drain hoses to the plastic plugs near the bottom of the bed. I cut the drain tubes down to about 4 inches long and used the holes in the sides of the stake pockets instead. No drilling required and a perfect fit.Update after 1 year:Trouble with this product. Not as durable as hoped. The panels are made from thin aluminum sheet metal bonded to a foam core. After about 9 months the aluminum started coming unglued from the foam and bowed out. It's completely loose on the underside of the tail section and about half loose on the mid panel. It's bowed out to the point you cannot even press it flat as if it has stretched or pulled out from the sides. Probably letting the panels fall closed eventually works the metal loose from the foam. The coating on the aluminum sheets is turning to powder and wipes off rather easily so it's turning from black to silver. The latch bar on the tail section just fell off one day! It was held on with a 1/2in wide strip of adhesive foam tape and seven small rivets. One day I closed the panel and it just fell right off. Warranty service has not been forthcoming. They said they would repeatedly send a kit to repair the latch but never have after months of pretending they didn't have my shipping address (when it was present prominently on every single message I sent them.) Rather frustrating so be prepared to not get any help from the manufacturer. I gave up on them and managed to reattach the latch bar with an ample amount of flexible marine glue and larger rivets. Drilled out the old rivets to slightly larger 3/16 size, cleaned, sanded, and cleaned the surfaces again. Took quite a bit of solvent and scraping to get off the old adhesive tape. I injected a generous amount of glue into the panel through the old rivet holes, put a solid bead of glue enough to squeeze out from the edges of the latch bar, clamped it all together along the whole length and put in about 11 3/16 aluminum rivets. It's there to stay now. Some of the other rubber trim is falling off now and needs to be glued on again.If you want this product I suggest you close the panels gently since they are not very durable. I do not plan to buy another bak cover unless they make improvements. I'm thinking a single piece hard cover is probably a better option now. It will look better longer and be a lot less frustrating.Warranty update:Amazingly Bak Industries does seem to honor their warranty and stand behind their product. After sending them a final message advising that I was giving up on their service they sent me a replacement cover. I was amazed. Buy with confidence.