KeySmart Classic - Compact Key Holder and Keychain Organizer (up to 14 Keys)

Very ergonomi, keeps the keys organised and neat in my pocket.

This is going to be a two part review: 1) Keysmart compact holder for 2-12 keys ( http://www.amazon.ca/gp/product/B00JXQQRJ0?redirect=true&ref_=cm_cr_ryp_prd_ttl_sol_1 ) 2) the Vagany keychain pocket tool GJ023D ( http://www.amazon.ca/gp/product/B00S4V2XDE?redirect=true&ref_=cm_cr_ryp_prd_ttl_sol_0 ) 1) i am impressed by the keysmart. after reading a few reviews claiming quality and durability issues i decided to go with the aluminum model instead of the titanium which i was originally looking at. that was a mistake. i should have gone with my first choice. under normal use and installation i cant see how people would encounter any issues relating to the product. i am 100% satisfied. the build quality is excellent, installation was easy, and keysmart delivered on all their claims. 2) this is actually much better quality than i was expecting. i purchased it specifically to go with my keysmart and was not expecting much. however, it is well build and quite strong. i would not hesitate to use it for some light prying. now for why this is a two part review. my intent for these purchases was to organize my keys yet still maintain the functionality i had with my attached keychain multitool (not the one in this review). instead of attacking my old multitool to the keysmart via a normal key ring i looked long and hard to find a product which i could install inside the keysmart. after quite a while looking i ordered both these products. despite the fact that they were in no way made to be used together they are almost a perfect match. the loop on the top portion of the multitool makes a perfect replacement for the included keysmart loop, the width of the tool is only slightly larger than the overall width of the keysmart so i am adding minimal bulk. and the length is almost perfect for the compact keysmart (it is about 1mm too long so there is some very slight rubbing between the tip of the tool and the spaces on the opposite end of the keysmart. the hole through which i installed the tool on the keysmart isnt perfectly centered in the tool so it does extend slightly on one side. however, these are very minor flaws in the system as a whole. these two products are almost made for each other. Now my plea to keysmart: PLEASE MAKE A TOOL OF YOUR OWN! with a little tweaking this would be perfect. some things i would like to see for an in-house solution would be: - make it that 1mm shorter to fit the compact keysmart perfectly. perhaps make a longer version for the extended model as well - keep the ruler on the sides (you guys already have the ability to laser engrave already for the marking), bottle opener, and wrench - the two flat portions on the tip can be used for standard or even phillips screws. the only change i would make here is the smaller of the two flat portions make into an actual phillips screwdriver - on the tip between the screwdrivers instead of whatever that is put a small rope cutter in there. - remove a bit of material between the circular hole towards the top and the upper loop to make them a bit closer. also center the hole so the tool would not extend more from one side of the keysmart - that teardrop thing i honestly dont know what it for. whatever. i have attached a couple photos as well.

KeySmart Classic | Compact Key Holder and Keychain Organizer (2-14 Keys, Blue) Ok, so I rarely write reviews, but I just have to on this one. Why? Because I find that the overwhelming majority of people who write bad reviews on this product are the same people who can't put together a ham sandwich. This product is ABSOLUTELY worth the money and the time. Read further! Ok, so here is the deal. We all look at the reviews to decide if our next purchase is going to be worth the money. I can tell you it IS! But you say, "OMG, look at all these horrible reviews!"....Ha, well, there is good reason for these bad reviews on this product that fall into two major categories. Read below! Here are the three most common things I have read and how I have debunked these as being hardly worth the negativity: 1) "Within days / weeks it broke! The screws, hardware have snapped...JUNK!" 1A) OK - Wow people. I can tell you EXACTLY why this is happening. Remember the people I said who couldn't put together ham sandwich? Yeah, these negative reviews come from them. Here's why! When you put together this product, you MUST use the little black spacers they provide to even out both sides of the brackets. WHY? BECAUSE, if you do NOT do this, it will create unnecessary tension on the screws. They are made out of a soft aluminum and will break if tension is applied for long periods of time. And why would you need spacers? Because you may have an un-even amount of keys on both sides, OR the keys are just different thicknesses. And there you have it! Make sure both sides are even, and you will have NO ISSUES. I PROMISE.I have had keysmart on my keyring for almost a YEAR with absolutely no issues at all. Still going strong. 2) "Not all my keys will fit due to different shapes, lengths, thicknesses". 2A) Ugh....Ok, yeah of course this product is not a SOLVE ALL for your keys. How could it be. They basically designed this product to accommodate the majority of key sizes and shapes. HOWEVER, this is where you have to think for a second before you buy. Look at your keyring, and look at the product. Does it LOOK like all your keys will fit from what the product pictures look like? No? Well, then you have to decide if you want to get it for the ones that DO fit and keep the rest on the ring, OR just not get it and be surprised when everything doesn't fit AND you don't have a ham sandwich to eat because you couldn't figure out how to open the package to get the ham out. At best, this product WILL WORK for all your keys. At WORST, this product will clean up your keyring some. 3) "It's a pain to get the keys to swivel out and I have to keep tightening it every month or so" 3A) - OMG THIS? Ok, seriously, we gotta kick these people out of the kitchen before they hurt themselves with a butter knife or something. In order to get the right tension, you will have to tighten to your desired torque level with a screwdriver or coin. Just simply tighten a little, and test. Also, YES since this is a screw based system, you will HAVE to give the screws a little twist every so often to keep everything good. Have I mentioned that you can use a COIN for this. It's no inconvenient. People....get out of the kitchen. You aren't safe there. OVERALL: I love this product. The only thing I hate is the fact that I didn't come up with it. But eh, whatever. Just remember, you get what you pay for, unless you can't make that ham sandwich. In that case, it'll always cost you a whole lot more. :) PS: Look at how nicely this cleans up my keyring from my pics. (also proof that I actually have these) :)

Great little gadget for storing common keys. Unfortunately if you have large bulky keys they do not fit, so you have to use a ring attached to this to carry these keys. If you only have common household keys, then I would highly recommend this.

مسمار الربط بيتفك وتسقط المفاتيح سيئ جدا جدا جدا

ich war mega erstaunt wie einfach und wie gut der KeySmart key ist und man hat 80% mehr platz in der Hosentasche würde es immer wieder kaufen.