EKR Custom Car Seat Covers for Select Honda Civic Sedan 2016 2017 2018 2019 2020 2021 (Rear Row Solid Folding Backrest) - Leatherette (Black with Red Trim)

The front seats fit correctly. I just ibstalled them, but didn't try them yet to check the quality. The backseats however dose not fit at all i even had to make some holes by using a knife. Civic sedan 2016

Several reviews have gone over how great these are, and honestly the front ones look like they came from Honda that way. I'd buy these again in a heartbeat. I'm mostly here to talk about the installation.This is likely going to be a several hour project. I spent at least an hour fighting with the bolt to get the back seat in place, but we'll go into detail on that later. Any difficulties I encountered installing these is on the part of Honda, NOT EKR or the product.First, make sure you take EVERYTHING out of the box they send you. Why? Because there's a little orange tool in there that is considerably smaller than my fat hands that makes a world of difference feeding these covers into tight places. I didn't notice it before I had the back seats on, and my very bruised hands would have been happy to have that. Now about that back seat... there's a 10mm bolt you need to remove that is just to the right (facing the seats) of the right-hand seat belt clip. A deep well socket and a short extension makes it easy to get to. Just pull up on the back of the seat or down on the cushion and it's pretty easy to spot. Putting this back in after I was finished? The bane of my existence and probably took 45 minutes of arguing with it on its own. About the middle of where both the left and right seats would be, there's a clip that you can squeeze and then lift the front of the cushion up. I have poor grip strength, so I opted for some adjustable pliers and in total the cushion was off within a couple minutes.Putting the covers on was relatively straightforward and simple. The elastic straps work really well and hold these in place just fine. It only took a few minutes actually get the covers on, strapped on, and for the back, to get the zippers closed. These covers seem to go on the same way Honda's seat coverings do, and in this case it greatly simplifies things.For the front seats, I recommend doing the base of the seats first. The instructions (which seemed to me to be much better than other reviewers have stated; probably have been updated since their reviews), show the back first. That's what I did, and while it doesn't complicate things, it does make putting the bottoms on a little more difficult.When I did the bases, I moved the front seats as far back as I could and tucked the straps through the back. I pushed the straps at the front of the seat as far under as I could. This way, you can slide the seats as far forward as they go and you'll have the straps peaking out the back and they're much easier to get that way, while also leaving you room to work from the back seat. Then do the backs of the front seats. You'll have to tilt them a ways back to get the headrests off (and those covers go in in about 30 seconds each), but it took another few minutes to get both backs on and zipped into place. The strap they include there ended up going on one of the stiff wires for the heated seats, as that was all I could really reach.All in all, it took me about four hours total to install these. Almost all of the straps running front to back make these considerably easier to put in than generic, one size does not fit all seat covers. If I didn't know better, I'd swear my car came from Honda looking like this. I would absolutely buy these again in the future. We'll see how long they hold up, but very happy with them as of right now.

Absolutely the best seat covers on the market - have purchase 4 sets for our vehicles. Always a factory fit had hold up great!When selling a car with these on - the person actually thought they were factory seats until I told them.

I was initially skeptical about these seat covers truly being a good fit. I ordered the black ones, but didn't care for the way they felt (kinda rubbery), so I returned them and got the neoprene ones - which i like the feel of much more. I watched a YouTube video that covered the installation. Really, I didn't get much from the video but it may be beneficial to some people. The hardest part to installing these seat covers was removing the lower (butt part) back seat. I had to watch a YouTube video to figure it out. It takes a 10mm socket with an extension and then you'll have to use your thumb and index finger to pull the two clips (one on the bottom of each side) toward the front seat. This will release the clip which holds the seat into place. I found that smacking the top part of the back seat (directly above the clip) repeatedly while pulling the clips forward (toward the front seat) helped a lot. Other than that, installation was pretty easy, with a start to finish time of about 90 minutes or so. There are a couple small wrinkles that I couldn't work out, but overall I'm pretty happy with them. They are seat covers and this wasn't a reapholstery job. I bought them to protect my beige seats that stain so easily. In summary: great fitting seat cover with a solid & sturdy feel for a reasonable price. Now for the true test --- time...

I am an over 60 grandma of 6 and my 2021 EX hatch is my baby. I have her for over a year and put these on a few weeks after I got her. As others have said, installation can be a pain and I did it in July in Florida outside so it was 2 evenings of sweat but these look custom stock and are a wonderful and durable fit. Maybe pricey but worth it!