ALITOVE 24V Power Supply 4A 96W AC/DC Adapter 100-240V AC to DC 24 Volt Converter 4amp 3.75A 3.5A 3A 2.5A Transformer 5.5x2.5mm for AMS-2-Pro LED Strip CCTV Camera LCD Monitor Massage Chair

I am using this on my Bambu Lab AMS 2 Pro connected to my P1S. What you need to know is that connected to the P1x series printers doesn't give you full control of the AMS. You can still do just about everything though including drying while printing. You don't have to have it turn the spools. You can leave them in with the filament still fed in. I've run the dryer for 8-12 hours at a time with no issues with the power supply, so it seems to be quite durable. The power plug is correct and easy to plug in. Its a good buy for your money.

2021-08-08 Increased to 5 star Seller was quick to send me replacement adapters. Just finally got around to the install today. 2021-07-02 5:30 PM Increased to 4 star Both power supplies confirmed working fine. Confirmed it is one bad female adapter connector, and possibly another slightly marginal one. 2nd one gets slightly warm. I would not expect a wire/connector to get warm at all. The one adapter seems to have a short in it. Squeezing ( very gently ) the body of the connector causes LED strip to flicker. Tested both PSUs with both strips and both connectors, connector was the issue. LED strips both OK, PSUs both OK. I have reached out to customer service in regards to the problem connector(s). Also some FYI. Power supplies are barely warm with no load, and according to a watt meter shows 0 watt draw with no load attached. So there is only neglagible loss when the devices connected to it are off. Dim blue LED stays lit when connected to wall power. 2021-07-02 4:00 PM 3 - star Will update review as I test more. Connected it on a test bench to a 47 watt light strand. 1/2 the power rating of the PSU. The provided adapter to wire the lights does not make a good connection with the PSU cable end. Additionally, most worrisome, it gets HOT. It was warm after 2 minutes and I disconnected, triple checked polarity/connection fit. Let it all cool down. Reconnected and let it stay connected for 5 minutes. At that point the adapter was too hot to handle comfortably. As for the poor fit, while connected I watch the power draw into the power supply from the wall outlet. It varies greatly, from 22 to 48 watts. If I squeeze the adaptor connector it will make a slightly better connection and go closer to 48 watts. Jiggle it a little and it drops as low as 20, LEDs flicker a bit. Power draw fluctuating. Bypassing that adapter everything seems OK. Note: I have not connected any dimmers/controllers in line, this is just PSU to LED strip for initial testing. I have 2 of everything for this install, I will test with other units / combinations to rule out the problem, but so far it seems to be the little adapter is just no good.

My original branded power supply for my LED string overheated and fried. This one is rated better and much higher quality than the original brand.

Does not work on AMS 2, wing dry while printing… waste of money. Quick update, seller reached out to me and refunded me, going to purchase from them the 6 amp, which seems to be working as people have in the reviews. Changing my review, and will purchase form them for sure. Thank you,

Works great with Bambu AMS Pro 2

Great fit works perfect with Bambu Labs AMS pro2

My AMS never has registered it.

Works great for my AMS 2 PRO, but be aware that it is slightly larger than the oem bambu adapter, so if you print a holder for bambu adapter, it won’t fit.

Works great for my HP laptop.

Good quality, works for my fogger

J’ai commandé ceci pour remplacer mon bloc d’alimentation de ma lampe RedSea Led90 pour le tier du prix d’un OEM.

works as described.

A good upgrade to my existing power supply.