3D Printer 6x20MM 24V 60W Ender3 High Temperature Heater Cartridge Element Compatible with V6 HOTEND PT100 Volcano MK8 Extruder CR10 Ender 3 V2 Ender 3 Pro 3D Printer (24V 60W)

Heats up much faster than the original heat cartridge. Installation was easier than expected. No need to upgrade firmware or replace the power supply. A quick PID tune is all that is necessary to ensure temp consistency. I was experiencing issues with the previous heater getting hot enough to properly melt some formulations of PLA and this would sometimes cause the extruder motor to skip. This heater cartridge appears to have solved that issue. Now I'm getting consistent melt and much better print results. Great price for such a useful upgrade and very fast shipping.

The product does get really hot and it heats faster than stock. Only downside is the wires are to short to reach the mainboard on my ender 3. But its a simple fix, just simply solder them to the red wires for the stock heater and it works perfectly. I've been constantly printing nylon at 290~300c with no issues. Pros -It's really hot -install was easy (soldering may be required) -Heats way faster than stock. -Fit's ender 3 Cons - It burned my hand

I got this as an upgrade to the heater on my modded out Ender 3. I wanted something to install on a Haldis Red Lizard 3 that could keep up with Klipper and nylon. This delivered. I haven't fiddled with it much when printing nylon (I mostly print PLA+), but it heats up insanely fast and will maintain within 0.5C while printing at 130mm/s+ with no problem provided you have its PID tuned correctly. Highly recommend but make sure you tune PID after install and make sure your printer has all overtemp safeties and shutoffs enabled. This is absolutely a fire hazard if improperly installed and configured; if left unchecked to runaway it can get hot enough to melt the aluminum hot end no problem.

My stock hotend got clogged and there was a massive glob of PLA stuck onto the heatblock covering the thermistor, nozzle, and heat cartridge so I had to replace all of them. I found this when looking for a new heat cartridge and couldn't be happier. This thing gets up to 210 Celsius in about 30 seconds compared to a minute/minute and a half for the stock 40W heater cartridge on my Ender 3 Pro. Just make sure to run a PID calibration before it's first use. My only complaint is that the wire attached is not quite long enough for me. An extra half meter and it would be perfect. I plan on splicing an extra length of equivalent gauge wire onto it to extend the cable length, but as is it works great. If you need a new heater cartridge, why not upgrade while you're at it?

I’m not sure if the item I received was a return because it lacked wire tires and zip ties, and it wasn’t wrapped nicely in the bag. However, it seems to be well-made. The wire feels like silicone, and it arrived with crimp ferrules on the ends. I forgot the measure the resistance but will update the review if I check it.

Had an issue of my Ender 3v2 stock heating element failing to maintain heat. Ordered this as a replacement and it fixed the problem. If I could change one thing about it, it would be adding about 2-3 inches of length to the cables - They're shorter than the stock, which makes cable management above the hot end a little more difficult because they won't fit in the original sleeve. It's not enough to knock down a start, but, just a mild annoyance that doesn't affect the new heater cart functionality.

The heater element, if 60W, will load your controller with roughly 2.5 Amps @ 24V. Most modern controller boards can easily handle this current / load. Didn't really measure the time it takes to heat to selected temperature on my older element and this one. But it seems to accelerate slightly the time to heat. It will get you a higher temperature on the nozzle, as supposed to a 40 W element. There are heater blocks made of copper instead of aluminum. They will cause a different heating response curve, so it is a good idea to run a PID calibration. In any case a PID tune is a good idea, with changes to your hot-end.

Works well, heats up quickly and after a pid tune holds it's temperature well. The cord is too short by almost a foot so it's a bit of a stretch to get it installed, it does install just not as comfortably. Installed on a mostly stock Ender 3v2.

This cartridge is great. it gets my hotend to 270c in about 15 seconds, and overall seems well built. Now happily installed in my Ender 3 and will remain so after the E3NG Conversion!

Excelente producto calienta muy rapido estable y muy buen alcance térmico