ICEBREAKER POP - 4 IN 1 - DISPENSER - MAKER - BIN - PACK - Make And Serve Ice Without Ever Touching It - The Sanitary Silicone Tray for Freezer With Lid - Cube Tray

I'm giving this FIVE STARS, despite some concerns. Why? Because regardless of my issues, this product does exactly what it claims to do, and it does it well! At least, so far. I've been using two of these for about a week now. I make at least one set of ice each per day. That means, I've made roughly 14-18 sets of ice so far and neither of my units have given me any trouble. Where I think people are going wrong is, frankly, not following directions. (1) There's a "max fill" line for a reason; water expands when it freezes, therefore, if you put water above the fill line, you're asking for cracks, leaks, and other issues. I filled to the line and poured out into a measuring cup – it's just a hair over 1 cup's worth of water, for those curious. (2) To break the ice into cubes you absolutely must press down with the palm of both hands - like when performing CPR - right in the center, basically on the strap. I press twice, flip, press twice, flip, press twice, flip, press twice. I don't normally need to press more than that. Ensure you are only pressing in the center of each side, never on the edges, and press pretty firmly. (3) Before you pull apart on the straps, be sure to open the cap! If you don't open the cap, you're probably going to end up with cracks, seal breaks, or broken trays. The cap must be opened before you pull apart because otherwise the suction prevents the halves from separating and puts extra stress on the plastic. (4) If you follow these steps, you don't really have to pull that hard. Sure, pull firmly, but not hard. The ice literally just "pops" out as the halves separate. I have yet to have any issues. Based on some of the negative reviews and some of the photos here, I just don't believe those folks are following the instructions. Many descriptions of leaking and bulging is likely attributed to overfilling beyond the "max" line. Many cracks and breaks is likely from people pulling so hard without opening the end or from them pressing in places other than the dead center. If you do have a leak, just press firmly around all the edges as it is certainly possible that the trays are not sealed fully. There should be no gaps between the outside of the tray (with the handle) and the tray itself. So what are my issues with the Nordic Icebreaker Pop 2.0? For one, let's start with the instructions. I've included a photo showing the conflicting directions regarding cleaning. When you open the unit for the first time, there's an insert that says to disassemble for cleaning. So I did. Boy was it difficult!!! It just would not come apart!! So I checked the little instruction booklet for tips, and there the instructions say specifically NOT to disassemble the unit for cleaning. This explains why it was so difficult to open up and clean (and an even bigger nightmare to reattach). Luckily I was able to get it all snapped back into place and sealed and have not had any leaks, but this is a major issue and could be part of people's issues with leaking after cleaning them. Secondly, I do have concerns about the longevity of the product. With the constant freezing and pressing and pulling, etc., etc., etc., I do worry that mini stress fractures will eventually start to form. It's just a thought for now, though; I haven't owned it long enough to say for sure, but just the physics of it all says the screws, handle, and/or plastic will eventually fracture. If it takes 10 years to fracture, then no issue, I got my value out of it. If it does so in 12 months or less, however, well – this thing is ridiculously expensive. Very overpriced, if you ask me – even though I'm very happy with it so far, I got it at it's lowest price ever during a recent pre-holiday sale. Even that was a bit high, but no where near as high as it's usual price. The point is, if it doesn't last, there's better value elsewhere. If it does, then money well spent, I suppose. Finally, it's a little unclear the difference between the original Icebreaker Pop and the Icebreaker Pop 2.0. The manufacturer's website is all but useless and clearly hasn't been updated (not to mention the grammatical errors, but I assume because English may not be their first language). Neither of the Amazon listing, nor any of the packaging or marketing materials, make clear what the difference is either. I also take issue with the lack of color options. Why so limiting? I'd love to get the Coca-Cola one, not for the branding, but because red is my favorite color! However, it's unclear whether that is the 2.0 version or not. All that being said, I still am giving this five-stars! Despite my concerns, I'm still overjoyed with how it's performed so far and having such large ice cubes for my water all day is wonderful! "Pro" Tip" I use a Tovolo ice cream container (the oval shaped one, 1.5 or 2.5 qt) to store my ice in. It's keeps it fresh and from absorbing freezer odors and it doesn't take up much space in the freezer either. By the time that container has emptied, both my Icebreaker Pop 2.0 units have solidified and produced me 18 more cubes a piece!

Mines did not work. I followed the directions. Filled the water up, under the max line. And it was a frozen block. I pushed down on both sides, expanded the panel, the ice was a complete frozen block. Itwasn't separated cubes. I banged it. I pressed on the sides, it was a frozen block that couldn't be broken into froze. Cubes. It was waste of money. May 31st 2026 I am updating my review to say, after many tries, I figured it out. I placed the tray laying on its back instead of up right in the freezer. The whole process is exhausting. I pressed the back to release the ice, many times, wait, do it again. Then pulled until it popped out. Shake. Shake. Shake. Shake. Shake. Shake. It worked. however the cubes are really small and do not last as long in my drink compared to medium or larger sized cubes. The concept is nice, having not to touch the cubes in transition. I'll keep it for when I entertain but rather use a ice cube tray. June1 2026 Ok...I entertained this weekend. The icebreaker Pop was a hit! I figured it out, its not so bad. I will order more in the future. Its a real space saver in the freezer.

I needed a tray that was compact and could fit in my almost-always-full-freezer and this certainly met those expectations. The plus was that I was able to make a small 1qt bag of ice in about a day (refilled and made ice 3x) The only con is that it is virtually impossible to see the fill line and the cubes are really small . The entire item is opaque! There is a marker for the fill line on the outside and where it meets on the inside. You can't see the water line from the outside and the hole is so small you can't really see if it's goes past the enclosure which stops right about how deep the lid goes in. (There is a connection inside from where the bottle meets the sides when collapsed) Overall, it is convenient for making ice and it worked really well standing up. I wish it made 24 ct or even 27 ct because the cubes are small. I didn't take it apart to clean. I just put soapy water inside and shook it very well and rinsed, so I can't comment on it if it leaks when taken apart and put back together. It is expensive for an ice tray but IMHO worth the price as a space saver. This tray is sturdy and built well. It took mashing it to loosen the ice cubes without discoloring or cracking. I will see if this hold up over time. Summer will be the real test as I will probably make about 4 bags to keep on hand. Will post an update review. UPDATE : 10/28/2022 Haven't had any issues with this ice tray maker. I have made a ton of ice all summer and tray is still holding up and hasn't cracked. I have no idea why so many purchasers are having bad experiences using this tray. I do still stress-DO NOT DISMANTLE EVER. I have never took it apart and only clean it with hot soapy water and several rinses. I also place container on a towel and let it sit for about 3 minutes after I take it out the freezer before crushing and removing ice. But I do that with regular ice trays as well so I always have all the cubes pop out and the tray not crack. I filled it up (I did figure out how to tell when it's full since there is no outside indicator of a fill line) and set it upright in my freezer to set. It has never leaked and it has no exterior integrity issues. I'm buying another one since it's $15 bucks now. I will update again in the near future to let you know how it holds up. I purchased the water version. I still stand by my first review. This is a well made ice tray.

Interesting, but strange contraption. It is tough to get the ice out, the hole is way too small. You also need to bang it on a hard surface and use a lot of strength to pull it apart. I'm strong and I struggled. If you don't rinse the ice tray after dispensing ice, your next ice will get all jacked up. It is functional, but quite a bit of hassle. I would not recommend it. The concept is great, but the execution leaves a lot to be desired.

Love these, was looking for a solution to make ice in an electric cooler where there are no flat surfaces for trays and these have worked like a charm. They don't leak, easy to fill, easy to open and get ice out. I like the size and shape of the cubes. Freezes overnight. Very pleased with this product.

Bought this so my ice doesn't have freezer taste and it exceeds all expectations. Perfect size for 32oz hydroflask. Compact design and easy to use. It also stands upright by design which makes it easy to set down while you pack the ice into whatever you're using it for. Plus it can stand in the freezer to make space. I love it so much I bought one for home and one for work.

Our family has tried several type of ice cube tray looking for that perfect tray, and finally, we settled on these. It has not been a perfect ride. It took a little while to figure how they could be easier to use. My wife and kids have had difficulty getting them open. After she broke the handle on two different trays, I watched how she opened them. She was not making sure the lid stayed clear from the opening. If the lid was just a little close, it would cause her great strain, and broken handles. I guarantee you, others here complaining about them breaking have done this. You must turn the lid 180° the other direction before trying to fully open the tray. Here's my process to fill them: 1. Fill the tray directly at the bottom of the top row of cubes. Ignore the fill line! Trust me, it makes all the difference. If you fill it past the point I recommend, the cubes are much more difficult to break up. Stand the tray on its end and fill it exactly between the 1st and 2nd row of cubes. 2. You don't have to wipe off the excess water before putting the tray in the refrigerator, but I don't like random ice bits all over the other items in the freezer. My process for retrieving ice: 1. Lay the tray flat on a hard surface and place the palm of your hand (or your elbow if you prefer) in the middle of the tray and give a quick, hard shove. You should start to hear the ice breaking up. 2. Flip the tray over and repeat step one, then flip and repeat one last time. No more crushing has ever been needed. 3. Pick up your ice tray and open the top. Spin the top 180°. Don't get lazy! Spin it 180° 4. Firmly slip 3 fingers from each hand through the ice tray grips on each side with the top on the other side of the ice tray, away from your body. This uses gravity to keep the top even less likely to accidentally fall back on the opening, creating suction as you're trying to spead the ice tray. The top falling back on the opening while spreading the tray is what breaks the handles. 5. Now that the tray is spread apart, close the top, shake vigorously while putting your other hand over the top (sometimes the top will accidentally open while shaking the tray and start throwing ice all over your kitchen). This might seem like a pita, but it's not once you do it a couple times. We have 8 of these for over a year. Once everyone in the family started using these instructions, the handles stopped breaking. It has been well over a year now. These trays went from a 3 star to a solid 5 star once I figured out these little changes. They are the best ones I've ever used. Best of luck.

What an amazing Product, You literally never have to touch your Ice again. Works really well, I haven't had to add any Ice to my Drinks all day long, it literally lasts that long. And you know those Blue Ice packs that you can freeze and add to your lunch box or cooler, these are literally the same thing as the Blue freezer packs

Quality and appearance are poor. Price is very high

Ho avuto modo di provare la vaschetta per ghiaccio Icebreaker Pop e devo dire che ne sono rimasto molto soddisfatto. Si tratta di un contenitore porta ghiaccio innovativo che presenta numerose caratteristiche interessanti. Innanzitutto, il design della vaschetta è molto moderno e accattivante. Le dimensioni contenute consentono di posizionarla facilmente nel congelatore senza che occupi troppo spazio. Inoltre, la forma allungata e snella rende il prodotto facile da maneggiare e da usare. La cosa che più mi ha colpito della vaschetta Icebreaker Pop è la possibilità di estrarre i cubetti di ghiaccio singolarmente, senza doverli frantumare con la forza come accade con le classiche vaschette rigide. Questo è possibile grazie ad un meccanismo innovativo presente nella vaschetta, che consente di far uscire i cubetti di ghiaccio uno alla volta, semplicemente premendo leggermente sul fondo. Altro aspetto interessante della vaschetta Icebreaker Pop è la presenza del coperchio, che impedisce al ghiaccio di assorbire gli odori presenti nel congelatore. Inoltre, il coperchio consente di impilare più vaschette una sopra l'altra, occupando così meno spazio nel congelatore. Infine, la vaschetta è realizzata in materiale resistente e di alta qualità, che la rende molto durevole e facile da pulire. In conclusione, se stai cercando una vaschetta per ghiaccio innovativa e di qualità, la Icebreaker Pop è sicuramente un'ottima scelta. La possibilità di estrarre i cubetti di ghiaccio singolarmente e la presenza del coperchio la rendono un prodotto estremamente pratico e funzionale.

I like it. After just a few refills the side has split open so the water spills out. Pushed it back together and seems to be holding.

I have had this product for just under two months. It was brilliant at first, so many beautiful ice cubes! If you followed the instructions they weren’t hard to free up, it was getting them out through the hole that was fidgety, but that was only a mild inconvenience. I soon figured out that if you run it under cold water for a moment (Often you can hear the ice begin to crack then) on each side before pressing on it it helps loosen things up. I’d bring this up to my boiling loft room having used half of the ice and stored this in my mini fridge so I wouldn’t have to go all the way down for ice. It kept the ice fairly well, but I don’t know how it would fair on a picnic or if you’re out somewhere hot without a mini fridge or cooler. I previously had given this a lower rating because it came apart. Turns out I was just dumb. Obviously these are, as advertised, able to be broken down for cleaning. When you put them together again, make sure you're trying to attach the sides the correct way up.

ya tengo mas del año con el, y ya no uso ni siquiera las hieleras tradicionales que tenia, algunos dicen que se rompen pero la verdad es que si sabes cuidar funcionan muy bien, no son nada fragiles.