HUANUO Triple Monitor Mount for 17 to 32 inch Screens, Adjustment Gaming Triple Monitor Stand with Swivel, Tilt, Rotation, Clamp & Grommet Kit

I've been using the HUANUO Triple Monitor Mount for a while now, and it's been a fantastic addition to my workspace. Here’s my experience with it: The first thing I noticed is how sturdy and well-built this mount is. Made from aerospace-grade aluminum, it feels solid and secure, even with three monitors attached. Each arm can hold monitors up to 32 inches and 17.6 lbs, which is perfect for my setup. The gas spring adjustment is smooth and allows for easy height, tilt, and swivel adjustments, making it simple to find the perfect viewing angle. One of the best features is the space-saving design. By elevating my monitors off the desk, it has freed up a lot of valuable workspace, making my desk look much more organized and less cluttered. The ability to rotate the monitors to portrait or landscape mode is also a big plus, especially for multitasking and coding. The installation process was straightforward, with clear instructions and all necessary hardware included. I opted for the C-clamp mount, which fits securely on my desk without any wobbling. There’s also a grommet mount option if you prefer that. On the downside, the initial setup took a bit of time, especially when adjusting the gas spring tension to balance the monitors correctly. It’s important to get this right to ensure the monitors stay in place. Additionally, this mount is best suited for wooden desks, as it might not be as stable on glass or particle board surfaces. Overall, the HUANUO Triple Monitor Mount has significantly improved my workspace ergonomics and efficiency. It’s sturdy, flexible, and offers great value for anyone looking to enhance their multi-monitor setup.

Ive used several dual monitor stands in the past and Ive been debating on getting one for my triple set up...after a lot of reading reviews I rolled the dice on this one. Super easy to put together with the instructions. Once you get it put together and mounted to your desk, either way clamp or through an access hole, you can adjust the monitor height. Super strong arms and joints...welds all look good and the white paint is clean. Holds 3 24" monitors with no issues! ADJUSTING TIPS Since the arms go up as they go out the only adjustment you need to do is the very top bolt for weight. As you turn the bolt, it takes several by the way, it will slowly adjust to a lighter monitor and slowly start to ease down. So basically a heavy monitor will take more tension than a light monitor. Just start turning and feeling the tension loosen as you push down on the monitor. Get it where you want it and slightly tighten it back up so it holds. If it springs back up then loosen it some more. It will go quite far down but they dont recommend putting the arm in a downward slated position. Just level. Get the left side adjusted and then set your middle monitor which can only be adjusted up and down. Then match the right monitor to the middle and left by repeating the steps to loosen the tension. Another tip if you have all of your monitors butted together edge to edge, if you find that your outside monitors moves up if you bump your desk, it has just a tad too much tension. Loosen it a little and then on the back of the monitors apply a small piece of tape from the outer to the middle monitor.....it will help hold the monitors since the middle one is non movable after you tighten down. The tension arms can be moved quit easily. If you have your PC backs open to the room and dont want to see tape try adding a small piece under the monitors edge at the bottom...it doesnt take much to hold them. Once you have the adjusting done you will love this stand. Ive been using for over a week no with issues. I didnt add the tape I mentioned above but I havent had that problem, only read about it in other reviews. Be patient the adjusting process can take some time to get it perfect. Took me about an hour but im pretty picky. Hope this helps. 5 stars from me! Id buy it again in a heartbeat.

OK I just finished getting all this setup so I'll do my review as I think it will be what it is without issue going forward. I'm going to start by saying this, if you are not mechanically inclined or do not know someone who is then move on to another option. This has a lot of little parts and pieces, and the assembly is tedious and time consuming to do it correctly, the directions are almost useless. I read the lack of directions mentioned in other reviews and it cannot be stated enough that they are poor if not borderline useless. If you take your time and don't rush it is somewhat obvious through the process of elimination on what pieces go where. As far as adjustments it's almost limitless but understand what you are working with, the small Allen head torque screws all around will NOT tighten to the point of stopping movement they will only serve to put a little tension to keeps arms from moving when bumped that is all they are designed to do so quit trying to crank them through the steel or you will strip them period! Second take the time to get familiar on the tension adjustments, small incremental turns will not give a major noticeable change. You will in fact have to do several turns to loosen the struts just to begin your adjustments, only adjust to the point the monitor isn't drooping on its own and the go the other direction just until it's trying to lift the monitor without you touching it and that's the set point for the weight of your individual monitor, do this before you try to align everything or you will start to go insane. SIDE NOTE: CLOCKWISE IS LOOSEN AND COUNTERCLOCKWISE IS TIGHTENING!! Lefty loosy righty tighty does not apply here!! I cannot say this enough the adjustment process can be long and tedious as well! DONT RUSH! I personally set 3 27" monitors up and have zero issues but used a level and took my time. I suggest setting the center monitor to the height you personally want and the use the level to set the tilt and the viewing angle you like. I set it the way I wanted then tightened the brackets on it tightly, so it was in its permanent position this made adjusting the other two ten times easier. Having a baseline will make your life easier I promise. I also read several complaints about bouncy this and moving that, I'm not sure what kind of desk or soft flooring they may have but I'm on hard wood floors and have a Secret Lab Magnus steel desk Everything is extremely solid, and I have zero wobble, shake, movement or whatever. Most of us have money tied up in these monitors and system's so try to take precautions and if you can shore up your desk or workspace and you won't have any issues with wobbles etc... I understand money can restrict some and I'm by no means loaded I'm disabled and on a strict budget and it took me a long time to save and slowly build my system and get the furniture I wanted so prioritize what you want verse what you need keep your gear safe!! I also read monitors move when bumped, this one puzzled me too, but yes they are adjustable monitors, what are you doing to make them move all over?? I game a lot and do the rage slam and toss things who games that has not done this? Nothing moves on me, so like I said I think its more the users than the product on 80% of these reviews. Is it perfect, NO! Is it worth the on sale price? Absolutely!!

Overall I love this item and unlike my last purchase, which I had to return, I plan to keep this one. PROS: Has two extension arms, meaning you have the middle part that connects to each side, plus an arm AND an additional arm, most would only have the middle part and one extension arm. This means for guys like me with 3 32" monitors you have the option of having them sit horizontally without having to sacrifice, IE one monitor is partially blocked by the other. As I noted I had to return a different brand and that was because of this. Weight - My monitors are roughly 15 1/2 pounds each and I didn't have any issues moving the arms around with the monitors connected. Says a lot about the stability that I'm talking about this product being able to hold a 15 lb monitor on a second arm extension, as opposed to one. Install time - About 10-15 minutes, 20 if you factor that I'm a moron who didn't check placement before setting everything up, then forced to disassemble and reassemble in the proper area. Bad joke aside was straight-forward setup but use your own screwdriver, the one that comes with this is limited. Range - Similar to what I've used in the past. Easy to lift upwards, downwards, tilt the monitor, rotate to portrait. Standard stuff CONS: Only one. The middle pole is a decent size, but not tall enough for me. If you're like me you want your monitors higher to reduce strain on your eyes (I'm 6' so I prefer not having to look downwards so much). In my situation even when I had the middle area at it's highest my middle monitor was too low. I ended up using a stand for my middle monitor instead of connecting. Checked with the manufacturer and unfortunately there wasn't an option to buy a taller stand or add an extension, so while I give this 5 stars IMO it's really 4.5 and only because of this limitation. TLDR - Great product, no regrets purchasing it. Can hold 3 horizontal 32" monitors but middle might be lower than you prefer.

I originally posted a 2 star review and said the mount could not fit 3 32" monitors. That review was meant for another brand, which was the case. I replaced that brand with this Huanuo and it was a night/day difference. The initial setup may be daunting for those who, much like the entitled Veruca Salt, want everything NOW, and proceed to kick and scream when they don't get it. If you have a little patience, and the most basic understanding if mechanics and physics, this stand is amazing. I am housing 3 32" LG ULtragear curved 180hz monitors with this mount, with ease. For those complaining about sag, if you tale two minutes to read the 2 pages of instructions, you'd see there's a set screw on the top of the piston arm to increase and decrease the upward force of said arm. Mine sagged too, as the arms came a little loose from the manufacturer, but low and behold, 4 or 5 revolutions of the screw, and, as if by magic, problem solved. One of the great things about this mount is that there is a separate mounting system for the center monitor, separate if course from the arms that have their own shared mounting system. This is clutch when you're trying to get all 3 monitors to perfectly align with no gaps between the bezels. It's also clutch to keep the center monitor square with the back wall, as one can loosen just the center, square it, adjust height, and then adjust the swing arm heights to it and be good to go. I built the wntire setup first, with no monitors, which seems common sense. I then installed the center monitor and got it to precisely where I wanted it. The last step was the adjust the height of the arms, I did this before installing the two outer monitors, again this should be obvious. I simply used the monitor mounting plates on the center as a guide. I lined up the outer arm mounting plates to it, keeping the arms as straight out as possible to allow maximum movement in both up and down travel. Once I got all the mourning plates pretty even by eye, I installed one monitor at a time to the arms, and positioned the monitors accordingly. Doing it this way, you can semi tighten all the set screws that you never have to use again BEFORE the monitors are installed, again, common sense, I know, it's difficult, and the only screw left to adjust is the arm piston screw which is on top amd insanely easy to fet to after the monitors are installed. This mount is crafted like a brick poop house and it's easy enough for a child to put together successfully, quite honestly. In comparison to its competition, in which I have been very courteous as to not mention names, this Huanuo mount is easily a clear winner. Have a little patience and, more importantly, be smarter than the thing you're working on.

Good price point and works great - love it Supports a 34" curved ultrawide and has no problems at all I'm quite tall so I needed something to keep me from craning my neck

Great quality for the price. I attached several pics and a video of it mounted to my electric sit/stand desk. I did order a thick metal plate designed for these mounts to sandwich on the desk being that my desktop is particle board I was concerned it would snap the desk where it clamps on at. I’m running 3 older 24" dell IPS monitors that are a bit heavier than most newer monitors and it handles them just fine. The gas powered arms were a little tricky to get adjusted just right and I still have one that needs some tweaks. When I adjust the screen menus with the screen buttons the monitor will slightly raise up on its own. Kinda annoying but I have not found a way to lock the arms in place once you have them setup the way you like. There is also only one screw underneath on the clamp and can be somewhat difficult to get tightened as the entire unit wants to turn. There are other units out there with dual screws that look like they would work better and prevent the headache of turning the entire setup when tightening. Not to mention they seem more secure. The cable management is great as I have two separate inputs going to each monitor and the power cable. All fit nicely in the sleeves and clips. Lastly there are no input plugs on this stand. Not really a con as you can clearly see that in the pictures and not docking any stars for it either. However there are other units out there that have built in USB ports, mic ports, etc that run around this same price point. All in for the price I would absolutely buy again and has been rock solid for a little over a month now with my sit/stand moving up and down multiple times a day with no wobble. Oh and the detachable vesa mounts that just clip into the arms are an amazing thing when installing your monitors. Just buy it. Hahaha

Got this for a Triple 32" monitor set up. I have 3 BenQ EW3270U monitors and decided on this arm. First of all, assembly was not too bad as long as you closely follow the instructions in the provided booklet. I opted on using the clamp as i have a Solid wood desk so no worries there. Once assembled, i was immediately worried that this thing would not be able to hold the weight of 3 32" monitors but to my surprise, once the monitors were installed, i was shocked as to how sturdy it is. I have a standing desk and moving the desk up and down does not cause the monitors to wobble or move. Very suprising. I bang on the desk and i notice very minimal movement but not too bad. Now on to the part where i give this arm a 3 star rating. If you have 32" monitors, they will BARELY Fit. it took me the better part of around an hour and a half to move/adjust the arms to just about get all 3 monitors in a position that is good for me. I have the middle monitor pointed right at me and the side monitors towed in toward the center. I wish the arms were just a little longer as you have only a limited amount of bend to tow them in. Its ok for now but not super happy. One thing i had to do is to have the 2 side monitor slightly in front of the middle monitor so i can have enough room to tow them in. it doesn't block the screen but maybe something for the manufacturer to think about. All in all, would i buy this again?.. sadly i'd say no, but for now, it works. UPDATE: after a couple of days, i just couldn't deal with the constant adjustments. I took it down and put my 3 32" monitors on a double and a single arm.. What a world of difference. Plenty of room now for tilit, tow in adjustments. I'm sure this arm is good for smaller than 32" but just didn't work for me.

Die Halterung kam inklusive einer recht guten Anleitung an. Die Halterung für 3 Monitore ist sehr groß. Der Standfuß ist stabil und Trägt die Monitore alle zusammen ohne irgendein Wackeln.. Die Verstellbaren Gasdruckfedern sind etwas fummelig einzustellen aber tun ihren Job auch gut. Ich habe 3x27" Monitore drauf. Was man dabei bedenken sollte ist die Anbringung der Halterung an einen Tisch der an einer Mauer liegt: Ja es ist möglich aber dadurch wird der Winkel indem die Monitore abstehen schon recht hoch. Besonders in meinem Fall (Tisch Maße:230x55x 04 cm Eigenbau). Tipp: Wenn du einen Tisch mit normalen Maßen hast montiere die Hauptstange etwas weiter in den Tisch hinein. Da Die Arme nach hinten abwinkeln braucht man da auch Platz. Das Problem wird geringer je größer der Monitor. Die maximal Montierbare Monitorgröße ist 32" Die Hauptstange ist entweder ohne Zerstörung klemmbar oder per Bohrung verschraubbar (Empfehlung). Der Preis scheint recht hoch aber dafür bekommt man auch Stabilität und Qualität. Die Halterung hat in den Profilen Kabelhalterungen integriert. Die Montage ist ruhig alleine Machbar. Einen zweiten zu haben kann jedoch hilfreich sein. In dem Fall konnte ich mich auf die Rezensionen zuvor verlassen. Die Qualität ist für ein Noname Produkt wirklich sehr gut. Zubehör kommt nummeriert und eingeschweißt (Kunststoff auf Karton). Alle nötigen Schrauben sind dabei. Die Verpackung kam ordentlich gesichert und somit unbeschädigt an.

After doing lots of research on monitor stands and solutions for three monitors, a lot of people recommended using three single monitor arms instead of a triple monitor mount due to stability issues found with a lot of triple monitor arms, especially as I was mounting three 27 inch monitors. I really did not want to go down this path as I wanted my setup to look as clean as possible without too many arms being mounted to my desk. I decided to risk it and order this triple monitor stand after reading some positive reviews. It arrived and it took me between 1-2 hours to set up which I thought was relatively reasonable given I had never set up monitor arms before. Installation went very smoothly, there was a worry that I may damage my Ikea worktop as it is veneer with particleboard (which the instructions for this mount said is not a suitable desk to mount on), but I decided to go ahead anyway. I did add a bit of hardwood between my desk and the clamp to give it a bit more strength and so far it has been perfectly fine. The mount itself is super adjustable and very stable. I've managed to get all three of my 27 inch monitors perfectly aligned, and there is enough space to angle them inwards. You could probably fit 32 inch monitors on here quite easily. I have had it all setup now for about a month and the monitors have not shifted even one bit. The outer monitors do wobble a little bit if my desk is wobbled or when I raise/lower my desk with the sit/stand feature, but its not a lot of wobble, and during normal usage (such as typing on my keyboard) they barely move. When they do wobble, they always return to their set place and do not shift at all. Having switched from using the stands that come with the monitor to this triple monitor arm, I have gained so much more desk space and my setup looks super clean and professional which is exactly the reason why I purchased this mount. If you are in a similar position as me, and are not sure whether this mount will suit you, I am sure you will be very happy with your purchase!

The arms are to short for 3x32". It's also a really weak construction. Keep away. Rear monitor mount hits the monitor holder so it cant be angled in a proper way.

Llegó a tiempo, excelente conductor de entrega y el producto funciona bien, paciencia y un poco de tiempo, bastante simple, método de ojal para mí y muy bonito. arrived on time, great delivery driver and product works well, patience and a bit of time, simple enough, grommet method for me and very neat looking

Fácil de instalar, robusto, bonito, útil. Definitivamente buena relación Calidad-Precio.