S9602A(4-Pack) S1108A(4-Pack) 15 7/8" Stainless Steel Heat Plate and Burner Replacement for Broil King 9625-84, 9625-87, 9635-84, 9635-87, Baron 320, Baron 340, Baron 420, Baron 440

I have a 3.5 year old Baron 320 model and this burner 4 pack fits perfectly and even leaves me with a spare burner. I installed it about 1 month ago and have cooked on it several times. The OEM burners lasted 3.5 years but probably needed replacement many months earlier as they were in really bad shape. The heat plates also fit perfectly and it's nice to have a spare. Not sure if they will last 3 years like the OEM, but initial impression is very positive. I do wish they would add in the cross-over as that was in really bad shape and I had been unable to use the spark starter recently. Replacing the cross-over requires removing the burners, so might as well make it a package. I was able to find that here on Amazon also, just make sure you get the correct set. Search for: Broil King Crossover Tube 15 5/16" x 1 5/8"

Hardest part of replacing these in my grill was getting the cotter pins out of the old rusty ones, these new ones fit perfectly and work just like the OEM ones did. They seem to be super high quality, I’d definitely recommend.

This was a repeat purchase after about 2 years. Easy replacement for the burners on my Broil King Baron. Also replaced the flame/gas spreader at the same time. The grill was hard to start as the old flame spreader was corroded to the point of having holes/gaps/blockage that didn't allow the flame/gas to spread properly. The burners had deteriorated to where the holes were burning through to each other so it wasn't a uniform flame distribution. This resolved that issue. Adding new burners, a new flame spreader piece, a new battery in the ignitor and possible new grids and you have renewed the life of your expensive grill. I am only getting about two years out of burners and 4 years out of a flame/gas spreader-ignitor. There were no instructions but install is easy. Use channel locks to loosen/wiggle the old burner tubes. Remove the hitch clip locking pins (new ones not included so save these if possible). Remove the burner tubes. Replace the flame spreader piece or clean it out to improve ignition. Adjust the new burner tube air gaps (screened openings) to the same size of your removed burner air gaps (easy with a Philips screwdriver), reinstall burners with hitch pin clips. These seem like quality parts and fits well but only lasted me about 2 years of frequent use.

The original burners in my grill were nine years old and starting to rot away. These replacements fit perfectly and function as designed.

This is a burner not even a year old, now broken for no reason. I was willing to shell out good money for these, and now this! Can't recommend.

The quality is great. If your thinking of replacing the insides of your broil king and reading the reviews to make up your mind I was doing the same... Except I didn't get much from the reviews but I'm hear to tell ya it's worth the $50. Especially knowing the $ it cost to buy the expensive *** grill to begin with... Just buy it and come back and thank me later :)

Old ones were all rusted out and popped them out and the new one slid in. My dad was pumped about this fathers day present. Feels like he can get another 4 years out of his grill.

great for price

Parts fit perfectly. Very pleased.

The holes that are drilled to be located in the crossover tube are way off. This makes it very hard to light. I'm returning them.

Brenner sind nach einem Jahr durchgerostet

Die Brenner haben keine Quer-Bohrungen, daher zünden nicht beide Seiten. Die Brenner gehen häufiger aus und die Flamme schlägt hinter den Drehknopf. Aufgrund dieser Problematik kann ich sie nicht weiterempfehlen.

Well priced great quality I will order agin