Wiper Blade Refill, Beigaon 28 inch Silicone Wiper Blade Refill for Replacement Windshield Wipers, (Strip Height: 11mm, Width: 6mm) Fit for Frameless Wiper Insert, DIY Cut to Size(Pack of 2)

This is my second time ordering these replacement blades - they lasted a whole year! I ordered this in the past and was very pleased with the quality of the blades and the ease of replacing. (On my Chevy Bolt you dont have to remove any plastic, you can just slide the old blade out through the little gap! Easy!) They worked flawlessly. What a great concept to avoid wasting all the plastic, and they lasted a long time!

[10/28] I tried to use the excess from the 17" blade and replace the rear insert. The 17" is the one I pulled the second channel off, and without that, it did not work. However, using the short piece I cut off for the 26" blade, it seems like it would still be very tricky, and may not work. The CRV rear wiper has the second channel similar to what these inserts have, but the CRV second channel is a little shorter than these silicone ones. If you spent a lot of time on it, you might be able to get it to work, but if the silicone is too jammed in there, it might not flex like you need it to. (I jammed the single channel scrap in with only one metal rod, and it would not flex enough, only the center was touching the glass) I found out a few helpful things. The blades are not 26", 17" and 12", they all measure shorter. I found the model numbers, and the millimeters are listed, and when converted to inches, it confirms what I measured. If you have a 2019 CRV the part numbers for just the inserts are: 76622-TDK-J02 - 650mm Front Drivers = 25.6” 76632-TZ3-A03 - 425mm - Front Passenger = 16.7” 76722-TRN-H01 - 300mm - Rear = 11.8” They are about $5 each online. [10/24/2022] I have a 2019 Honda CRV. it came with nice blade-style windshield wipers in the front. This means replacing the "insert" (rubber/silicone) is perfect since the frame is good. Everyone online says silicone lasts longer than rubber, and most of the amazon listings that say silicone in the title, the reviews say they are rubber. So that's how I arrived at buying these. I measured the old rubber, and they are 6mm wide (wiper inserts are usually 6, 8 and 10 mm). However, I did not measure the height. The OEM inserts have one channel to slide into the frame these silicone ones have 2 channels. You can snip the end, and the one channel will tear off cleanly. But I would not recommend it. This is where the catch is. I snipped the second channel off, and the insert is now exactly the height of the OEM one. BUT the remaining channel is not 6mm. I did not measure it, but it is slightly fatter, just enough to not go in smooth. The problem is that sliding it into the channel is a giant pain in the butt. I ended up getting it in about 4 inches, and then pulling on it so hard the end popped out of the channel, that ended up helping though, I could get a better grip on it and pulled it really hard (it was stretching 3-4" but it's silicone, it appears fine - I can say 5 stars for sturdiness since it didn’t break). I then overpulled the silicone insert (because I needed to get the end back in that I had popped out). I then pulled the insert back to the right length while guiding it into the channel. Then I cut the excess off, and stuffed the last inch into the frame. I did this on my 17" blade. My 26” frame would have been a nightmare. Next, for my 26" blade, I left the silicone insert alone, and it took about 30 seconds and I was done. So now my 26" wiper sits taller than the OEM did, the 17" sits at the same height as the OEM. The next day we got a light mist, I tried these out, there was almost no noise (barely any water, plus freshly cleaned is the perfect recipe for a squeak). Both worked fine, so the extra height probably does not matter. In a harder rain, it might make a difference, or the wear and tear might be different. So, I will update this review if I notice anything different about the two different wipers.

I decided to go with cheaper route using this 2 for 1 wiper blade instead of paying more than double for PIAA 28' blade. There are people complaining about splitting wiper blades that are joined together. This is easier than opening potato chip bag. If you cant figure out how to split two wiper blades you shouldnt be attempting to install this on your car. So on surface this seems like good deal and it may be. The problem is with two things 1. you have re-use two metal blades that attach to the top groove of the blade. This is fine except you they dont stay in place. So workaround is to hold the part of metal blades and rubber blade close to wiper assembly and carefully insert it. It took me few tries to figure out how to do it but its not rocket science. You just have to make sure wiper frame guide glides into the 2nd groove from top. You'll see what I mean once you do it. 2. Rubber blades dont have notches to prevent them from being pulled out. I'm not sure how they'll hold when blades are used in heavy rain. I'll report back after several month of usage to see if this is working out. So in summary - installation will be slightly harder and lack of notch on the rubber blade seems bit iffy. I'll report back later on how the lack of notch affects its operation over long term

I've replaced a lot of wipers on a lot of cars over the years. This time, I needed to do a replacement on a 2023 Chevy Bolt - which has a wonky wiper arrangement (the two front wipers are radically different sizes - my guess is the rear is yet another size). My normal spots for buying them (enter the year/make/model, get a link to what you need) had no matches so I had to dig a little further and found a link to this product. It arrived and with a little fiddling I put the refill in, mounted back on the car, and immediately had to drive in the rain - awesome. Things to note - the "height" of the refill (distance from the metal part of the blade to your windshield) is adjustable. The out of the box height was too tall for my Bolt (it wouldn't fit in the slot), but the part of the refill that is farthest from your windshield is layered. A quick (but careful) slice along the length of the refill with a very sharp knife removed the bottom layer (like a layered cake) and it fit perfectly. You can cut the refill to length with any utility scissors (like kitchen shears) or a knife. This was significantly less expensive than a new set of blades, less wasteful, and if you've ever fiddled with one of those "universal" attachment gizmos - less frustrating to boot. The quality of the "wipe" was quite high - clean/clear windshield, low noise even when there was little water on the glass, etc.

Fits the front blades for my 2023 Chevy Bolt EUV. Wiper blades are kind of hard to find for this car since it uses a weird connector. It was pretty easy to remove the old rubber, cut the new silicone rubber to match the length, and insert the new silicone rubber into the blade. It seems to work well, and this was a fraction of the price of a new blade from the dealer (and even those are apparently hard to find). I saw another review saying they also replaced the rear blade's insert with this. I didn't try that because I'm not confident it would stay firmly in place with how the rear blade is designed. There's enough length, but I think the insert would slide out because it doesn't have a locking mechanism built into it. The front blades work because the front blades themselves securely hold the insert in place. Anyway, I'm more concerned about the front blades than the rear, so I'm happy with the result. I tested briefly in the garage with washer fluid. I haven't road tested it with actual rain yet, but I don't expect any issues. I would buy this again.

This was highly disappointing. We have ordered from this company before and never had an issue. This was not the usual product that is typically shipped out. This was clearly a cheaper, inferior product. Also only received 1 set, event though the listing states 2 sets. Would not recommend to anyone.

My BMW iX windshield wipers were no longer safely clearing my windshield, and of course they want to sell you complete set of $$$ when the only thing that actually needs to be replaced is the rubber portion only. This does the trick. Will be buying more in the future!

I was happy enough with my first purchase that I ordered 2 more sets (1 pair each). The Honda OEM refills were about $30 for a set, and I got 2 sets for $16. I just removed the old refill, slid the new one in, cut it off with a sharp knife, and tucked it into the blade (2023 Accord). It wipes cleanly and appears very secure.

Easy replacement on my Bolt Euv !

Much cheaper then replacing the whole wiper, I will forever be using these in the future

Surprisingly I received a used blade! The bag had two blades, one clearly used (dirty, worn, has a part number on one end of it and a slightly different shape!! The other blade looks like a new one. How could this happen???? Not impressed! Should be less than one star as this is fraud

Price worthy and easy to install

Only lasted 2 weeks now the right one is squeaking and both are leaving a haze.. The haze was there from day 1 but the squeaking has just started. I cleaned them and the window but made no difference. I’m going to Halfords to buy Bosch aero twin and these are going into the bin.