Promise Epoxy Deep Pour Epoxy Resin Kit 3 Gallon, Up to 4" Pouring Depth

I used this for an epoxy river table. It worked great, was crystal clear, and dried hard. A few tips: -This is very thin - it flows like water. If you have any leaks, it may all leak out. I did an initial pour of a small amount and tilted the table so it flowed into all corners and cracks. I let it cure for ~18 hours to partially harden and seal any leaks. Then I poured the rest. -Make sure your table is exactly leveled. This epoxy will level itself fairly perfectly, so any tilt in the table will result in unevenness in the thickness of the epoxy. -This takes a couple of days to "harden". It may be unnecessary, but I gave mine a week before putting it into use. If you are uncertain, save some epoxy in the pot you mixed it in and test its hardness by pushing a fingernail into it. -If you want swirls in tinted epoxy, it needs to be done when the epoxy gels. At the temperature I was working at, it took about 12 hours. I used mica-based tint, and it seemed to settle just a bit. So when I gently stirred the epoxy, it came out with nice swirl patterns. You must do this very slowly or you risk getting bubbles that will not come out. Definitely test on a scrap piece to see how long you need to wait, and how gently you need to swirl. Keep checking on it (and maybe re-mixing) every half hour since the swirl pattern can start to settle out even when the epoxy is gelled. You can also try mixing in another color, but I haven't tried this yet. -be careful of dust. This product is so mirror smooth, any dust landing on sticky epoxy can be visible in the finished product.

I’ve always had great success with Promise Epoxy. As long as you weigh out your ratios, it cures well and is reliable. There isn’t any color and it doesn’t smell much at all. Cure time generally is the claimed 72 hours but I’ve found after 48 hours it’s nearly completely set, and rarely will take longer than 72 for a full cure. It accepts dyes, mica powder, and glitter very well without impacting the cure. I did have some challenges with a true large volume deep pour and the epoxy rapidly hardening but I do think that may have been my fault with the mixture. Doing small amounts I’ve always had great success.

Won’t use anything else… worth every dime.. crystal clear results

I ordered this to make live edge cutting (Charcuterie ) boards. I’m not a wood worker, so Its just learning for me. I ordered this based on reviews and price point. First, it pours just fine. I didnt use a funnel or anything other than 1000ml plastic cups. They have measurements on them. Second it mixed well with a silicone paddle. I was able to make three boards with this, although i did over mix on each of them. I covered the entire surface of my wood each time. This mixed well with the pigments I purchased with a few questions. I have not dialed in the right time frame to get the right swirl pattern. One session settled quickly. This seem to cure the best around 70-71 degrees. However it took a full 48 hours to harden and most I let sit for 72 or more before finishing. They polish well to 2000 grit, and upot further inspection I believe I should have sanded and buffed more. These did not surface well through the planer we used. Believe me when I saw this is a professional quality 20” carbide tipped planer. We instead built a router jig and that did the trick. Overall I am pleased. Check the photos for the output.

This was my first deep pour project and after reading a lot of reviews of numerous products I opted to go with Incredible Solutions. All the deep pour products seem to have the same negative feedback regarding slow cure times but I guess that's what makes it deep pourable. Living in South Texas there are not a lot of days in the year which fall within the manufacturer's recommended temperature range and the wife is not going to let me do this in the house. I caught a day that was right on the edge of the maximum temperature for optimum cure but put a small fan on it just to make sure. It was a 1 1/4" pour in 32" round table. In 24 hours it was gelled, soft and sticky, 48 hours it was hard enough to touch and not leave a fingerprint but soft. After 72 hours I don't want to say it was cured through and through but definitely hard enough to pull the form. I kept it on a flat level surface for a couple more days before sanding. I had degassed the original mix and the final product was completely clear and not a bubble to be seen. I haven't finished the project but this was a much better experience than I had anticipated. Great product. Side note: the ambient temperature varied from 78 down to 75 or so at night. Humidity, as always here, was 90%+. It will probably be fall here before I get that lucky with the temperature again though.

I bought a gallon to make a memorial for our grandmother who died last year, so picked up flowers from her funeral and dry them. I made this for my mother in law, but the other sons loved it so I decided to make more. So I bought another gallon and right from the the beginning something for not right. The epoxy was cloudy and I had to put it in warm water for the cloudiness to go away. Talk to customers service and they said that I was probably storing it in a cold place wich I wasn't (I have had worked with epoxy before and I know how store it and work with them). I also sent and email to the manufacturer and they never responded. Now I am very upset because I ruined the last flowers I had and the project came up horrible. Not going to purchase this again cause you never know how the product is going to be.

Good quality epoxy. Bubble free and superior clarity. I poured an 1 1/2” deep table and it was cured in 4 days @ 70 degrees.

I used this epoxy to build a river desktop for a height adjustable desk in my home office. I have used tabletop epoxy in the past, so I was familiar with how to work with epoxy. I watched tons of YouTube videos on river tables before doing this project. Promise deep pour epoxy was very easy to work with and the instructions are very helpful. The desktop I built was 1.5 inches thick. To be on the safe side I poured 1/2 inch the first day and the remainder the second day. I purchased white metallic powder from Michael’s. For bubbles I used alcohol and propane torch. I waited the full 7 days before I proceeded with planning and sanding. The desk turned out great and I would definitely buy this epoxy again.

GARBAGE AVOID If I could give this a minus one I would this company is a scam. Please do not buy this. You will ruin all your projects. Look at the video. I attached. It came with hardened bits of epoxy at the bottom. It’s a poor quality. AVOID AT ALL COSTS I lost THOUSANDS OF DOLLARS BECAUSE OF THIS I’ve never had this happen to me I’ve been making furniture for 10 years and this is the first time I’ve ever seen this!!!

pretty good epoxy. i did a deep pour about 2 inches thick and had no issues. when flattening on a CNC after about 2 weeks of curing, it was hard enough to cut without dulling tools, but not soft enoug hto bung up the blades. so i would use it again.

1/3 of both part A bottles were hard chunks and useless. Tried to warm to make useable, and did not work. Contacted seller, did not respond, don't waste your time or money or ruin a project with this junk

Chunks of hardened part B ruined my pour. Checked the label and discovered that both A & B were 2.5 years old!!! Most epoxy has a shelf life of a year...some 6 months, unopened. Ruined 7.5 gallons, including another brand. Pretty bad selling expired product.