Anti Vibration Pads for Washing Machine with Tank Tread Grip - 4 Pack + Level - Fits Most Round Feet up to 1.75” - Stops Washer Dryer from Moving - Rubber Antivibration Stabilizer for Leveling Washer

Got 2 packs of these 2 1/2 years ago after the earthquake here in NYC. Put em underneath my bed stands. Working out great since. Think it might've dampened general neighbor noise so I can sleep just the slightest bit better.

Best thing ever I live in a mobile home and my washer shook my dining room wall so bad I thought my shelves would fall but now nothing vibrates at all so quiet .

Warning: Do not use the level provided as it is very innacurate!!! It is too short to measure the tilt of your appliance and instead will read the imperfect bow of sheet metal. The pads did a great job of dampening vibration and noise...5 star rating here. The level provided was a zero star and could have caused issues if I relied on it instead of my trusty "real" level. Why even provide an innacurate level? Instead use a long level that spans the appliance front to back & side to side.

I bought these to replace older pads that were hollow on the bottom. The hollow pads were squished flat and became useless. These pads are solid and heavy for their size. That’s how I know they are good quality. I love the bubble level included so you can verify your washer/dryer are level or need adjusting. After installing these pads I ran a load of laundry in my washer. On the opposite side of the wall is a bathroom toilet. During the spin cycle of our LG washer the vibrations were bad. I was afraid of being shaken off the toilet and dropping a bomb on the floor instead ! The spin cycle always makes the most noise. But with these pads installed there were no vibrations that I noticed. Our laundry room is on the 2nd floor. Previously the vibrations were so loud I thought our ceiling drywall would crumble down on us while watching tv in our living room ! With no more vibrations the noise has been greatly reduced. We can watch tv in peace and I can use the can without my parts bouncing around. Some reviewers may complain about the new rubber smell but it doesn’t bother me. These pads were money well spent. If u have a second floor laundry room I especially recommend these pads !

If you have your washer in a drain pan with tapered sides, these might not sit flat depending on the foot placement of your particular machines. We recently purchased a set of these to go with our new Super Capacity LG Washer with the matching dryer. Our old set was the standard 27" wide. The new set is 29" wide. Plastic drain pans measuring 30x33" on the outside have tapered edges resulting with the interior dimensions of 29x32. Because the feet on the LG washer are VERY near the outer edges, these won't lay completely flat in the pan with the washer in the slots. They kind of sit up on the edge on each corner. They are pretty firm, but we were able to finally get them all properly aligned under each foot with all pads slightly sitting on the edge of the pan. I was concerned the lack of solid footing might cause a problem, but I was pleasantly surprised. Even when spinning a king size comforter and its associated bedding, the washing machine barely moved. It is the quietest king size wash that's ever occurred in our laundry room over the decades. I plan or changing the plastic pan for a genuine 30x33" stainless steel pan to correct the issue. I wouldn't bother if the plastic pan drain hadn't been so poorly executed. I would definitely recommend these. Others complained about the off-gassing. They do have a scent, but it's pretty slight. I'm sensitive to lots of smells and I had to hold these up to my nose to really smell them. My hands didn't smell bad after LOTS of manipulation trying to get one securely under washer foot. Well worth the money and the included level was invaluable. Best part is that it's magnetic and very easy to secure to the washer to measure side-to-side, front-to-back, and corner-to-corner. Good stuff!

Bought these to do two things: to stabilize my washer (cut down movement, vibration and noise) and to protect my newly installed laundry room floors. I will say they have cut down some on movement (my older top-loading washer does not travel as far with these feet). My washer used to push my dryer into the wall it traveled so much, but it did that rather quietly. That is NOT the case now. I swear the noise level seems to be much HIGHER than before (it’s like all the vibration and movement just echoes in place). We cannot watch tv two rooms away without turning up the volume at least 5-8 notches when the washer is going, so I just don’t wash clothes if we are trying to relax with tv. The one goal that seems to be working - though I’m not sure how - is that it does not seem to be tearing holes in the floor. I’m keeping an eye on that and will remove the feet if necessary, but the feet were a real pain to put on (especially on the back legs) because they don’t slide into place (not supposed to). Hence you need 2 people to install - one strong enough to hold washer up and one with long enough arms to reach back to place feet in just the right spots so the washer can be lowered down perfectly on the feet. It’s a trial and error (more than one try unless you get really lucky) process. Would I buy them again? No, but do I want to crawl back undr the washer to remove them? No. They work fine under the dryer, but it did not travel nor was it noisy to begin with. I just wanted both appliances the same height and the floors protected, so we put the feet under both.

Works great! Thick. Damper all vibration!

So, I had been chasing this really bad vibration issue with a new washer that we purchased. It's a bit unique as the washer is upstairs and sits in a rubber pan on a wood/vinyl floor (vs concrete). I had done some research on balancing/leveling the washer and had gotten it as good as I could with the base system, but it was still noisy and vibrating the whole house for certain loads. Note: If you are having a problem in this area, one important tip that I came across that didn't dawn on me was to shake the washer from corner-to-corner. Even if it is level, if it still moves pretty freely, you're going to get vibration noise and movement. I had to lift and level a few times as the rubber pan mine sits in has ribs that the pedestal sits on, so had to lift it high enough so that it didn't sit on those. And the pedestal height is probably a contributing factor, but we are not getting rid of the pedestal! ;) Although the supports did not completely alleviate the vibration and noise, they did significantly decrease the vibration and noise. Enough that I thought there were well worth the purchase price and enough that I would say they removed almost 90 to 95% of the problem. The increased footprint was clearly a big help and they lifted a bit higher than the feet adjustments that I had previously made so they were clearing the ribs on the rubber pan. Before installing these, I reset the pedestal feet back to 0 height. For me, well worth the purchase. The pictures are of the feet installed. The video (you can only upload one!) is after they were installed and I'm washing clothes and a large Judo Gi (many times the culprit). Installation Notes: Due to the location of my washer I used a yoga ball and air compressor to lift the washer and place the feet. Good thing I have long arms. I have included a couple of photos of those as well.

love them ! so solid they might just outlive me !

A little pricy .. But it is the only one that realy works .. All ather are plastic .. This one is Rubber and does not move.

Great product which hs helped my stacked washing machine and dryer from moving around and reduced noise ..the product is well made and sturdy and at a great price point

My washing machine went wild on these, hockey pucks worked better. Too be fair I still replaced the washer because of excessive vibration but the replacement machine works very well on pucks. I think it very much depends on the rigidity of your floor what will work best. Returned these for a refund.

Big chunky and solid boots for the heavy floor grinding machinery. I have mine cushioning a heavy Miele washing machine with a dryer on top to prevent the washing machine feet from drilling through the floor tile.