Minus Pad 8 120x20x3.0 mm Thermal Pad GPU SSD Laptop

Been using my 1TB WD SATA M.2 in my enclosure and the thermal pads that came with it were garbage honestly probably 0.5mm. Bought this to bring down temps. The good thing about my case was that I was able to apply some thermal pad the the top and bottom of the SSD with no problem and actually helped me screw the SSD down a lot fast so can’t complain. Excellent pricing for this SSD and the thickness is excellent for small enclosures or motherboard m.2 SSDs. With the amount they give you I was also able to apply some of the thermal pad to the enclosure controller and it fit in the enclosure with no gaps in the pad. Fixed the heating problems I was having. And was pretty durable when I had to reapply it compared to other thermal pad brands. The SSD is running at 35 degrees C while copying over 400GB of DATA to my NAS drive and my external drive.

I have a used Dell XPS M1530 laptop that I bought several years ago and my bad, I never replaced the thermal paste and pad after receiving it. I needed a replacement thermal interface pad for the CPU, the original being Silicone based. I wanted something better. This product was easy to trim and cut to the size of the heat sink surface. It has a double sticky side, and I wasn't sure if one side was prefered to face down or not, but I don't think it matters. The gap depth was 1 MM and that is what I ordered and it fit perfect. Since this laptop started to have constant high fan output I knew it needed to be checked. There was also a dust clog on the end of the fan assembly so I took the cover off of the CPU fan (four tiny screws) and used a clean, soft paint brush to clean it. Now the laptop runs quiet.

Used on my PS4 phat launch day model , it workes great one sheet did my entire system with a little left over (not a lot)thermal grizzly products never disappoint ,they are one of the best at what they do

Effective easy the best for my high end laptop dell 7770 with rtx and i9 and yeah does not overheat now

It works very nice !

Its easy to use, it is delicate. But seems to work

it comes wit protective layer on both sides , so u have to remove protective layer from both sides. The side with texture is easy to remove the protective layer , other side is without texture and I almost missed it

I have always thought my PS4 pro (launch model) was loud from day 1. The day warranty was up, I pulled it apart to try and replace the thermal paste in an effort to drop down the temps, and by extension, the fan noise. I completely overlooked the thermal pads that time, and it is no wonder why it didn't quiet down a lot. After having enough of the jet engine sound when playing demanding games, I started to look at other ways to help cool it down. After checking for thickness, I decided to try and replace the thermal pads with something better. Upon closer inspection this time, it is amazing this thing could cool at all. The factory pads on the VRM's are maybe half the size they need to be, and weren't even aligned at the centers. Pads on the ram looked better size-wise, but were still not aligned. I purchased this, and it is just enough to get a PS4 pro done on both the VRMs as well as memory, with basically just scrap pieces to spare. Cut all pads to fit, and made sure they were centered when putting together. It is a night and day difference for me. Between this and my trusty MX4 thermal paste, she is running much cooler now! It still ramps up quite a bit under load, but it is at least a large step below Boeing 747 takeoff! Kind of spendy for the amount of material you are buying..but it works great, and I am super happy with the results!

Ps4 pro went from jet engine to quiet as a tomb, put one on the hdmi chip too, makes all the difference.

The Thermal Grizzly Pad was quite an interesting item to use for cooling down heat intensive devices such as the Playstation 4. It does look like a long stick of gum or a Laffy Taffy after opening up the sealed package. Both flat sides of the pad were stick onto a thin plastic cover for protection of dirt and debris. The plastic cover can be quite tough to mark any measurements without using a fine marker or a wet pen. Using a fine sharp tool, it can be cut into near to exact measured pieces for your project. In this project of mine for instance, I used it to help cool down my original PS4, replacing the stock thermal pads. After testing my PS4 out for few hours with the new pads, I've noticed quite a difference in cooling that help lessen the use of the stock fan, so it doesn't sound too much like a jet engine. I would use this product again to replace other heat intensive devices in the near future.

Bought from Scorpzon trading, received freshly imported, totally geniune product, when I checked the label, found that the seller Scorpzon is the official importer for thermal grizzly products in India, came in a resealable pouch, used it for my MSI gaming Laptop to replace the factory installed thermal pads. Works as advertised, easy to stick, don't forget to remove the protective film from both side of pad before installing.

Usé este thermalpad para las VRM de mi GTX 1080 8X de MSI. Había cumplido la garantía y nunca se le había realizado un mantenimiento y las temperaturas estaban ya rondando los 78ºC mientras jugaba, hacia stream y mantenía 2 monitores. Cuando abrí la gráfica a parte de sacar pelusa como para rellenar un sofá, vi que el thermalpad que venia de fabrica estaba ya negro completamente y de una textura un poco viscosa. Cuando lo cambié aproveché para cambiarle la pasta térmica ya que que la de fabrica estaba seca como solidificada y puse la pasta Arctic MX-4. Cuando inicié el ordenador la gráfica en modo reposo (2 monitores, viendo Youtube (sucedaneo) y charlando por Discord marcaba un rango de entre 33ºc - 37ºc. Pasando test de stress GPU de FurMarks no sobrepasa de los 67ºC. Un acierto de 10, de ahí mis 5 estrellas. Es fácil de manipular, cortar o instalar.

This a great product to mantain low temperatures of electronic components around CPU and GPU. It's a bit expensive but quality is good. Easy to apply due to its due to small size and good quality paste. The Functionality and performance increases when used in combination with Kryonaut. Temperature around GPU and CPU were around 80-90 Deg celcius. After application the Temp of device hovers between 40-50 at room temperature.